Don't Miss

Air Intake Inlet Manifold Flap Adjuster control unit diagnostic and repair guide

By on January 7, 2017
fix-air-intake-control-unit-flab-adjuster

 

 

 

 

 

 

 

 

 

This is actually an electronic control unit for the intake manifold flap for several VW and Audi cars. I assume they are on other vehicle too but in some other shape. I would try to demonstrate as simple as I can how this unit is build up and how to diagnose.

air-intake-inlet-manifold-flap-adjuster-control-unit

Days ago, I got this part in my mailbox for diagnosing and repairing from a nearby car repairer garage. Actually the car comes up with several error codes and one of them was the ” P2015 – intake manifold damper sensor, implausible signal “. The first think what went over my head was, I deal with an electronic control unit who has an implausible signal on his sensor part.




Ok, most of the technicians would suggest you to buy a new intake manifold and change your intake manifold in your car. This is actually a big mistake and a very expensive game and you didn’t solve your problem with it. Let’s talk about how this unit is build up and from where directly this implausible signal is screaming from.

flap-adjuster-control-unit-diagnostic-and-repair

 

This is an example of an air intake manifold with an electronic control unit.

air-intake-control-unit-repair

The electronic control unit is build up from several gears, a DC 12V brushless motor, a flap position sensor part and a magnet. It is very similar as the electronic throttle body as I wrote in one of my article before. Here is how this unit looks under the hood.

repair-air-intake-control

The most major problems why this unit is in a bad condition:

–              Dirt in the air intake manifold and the flaps can’t move freely.

–              Blocked flaps in the air intake manifold.

–              Brocken parts like a broken spring or failed / broken gear.

–              Bad control unit.

–              Bad electro motor.

–              Some calibration problem as it was the case in this unit, etc.

The spring:

The spring is use to move back the flaps to its initial point. If ECU requests a specific position then the motor has to overcome the power of the spring and moves the flaps in a desired position what is initialized by the ECU.

The magnet:

The magnet is actually in a relation with a hall sensor which is integrated into the black housing. It is used to tell the ECU where the flaps are until operation condition.

The motor:

The motor is used to move the flaps to a desired position or angle what is requested by the ECU

The motor is actually a 12v DC brushless component.

repairing-air-intake-control

The diagram part:

how-to-repair-air-intake-control-unit

On the J623 you can see the T60/50 or T60/27 or T60/10 this means the 60pin connector where the wiring is exactly on the 50 or 27 or 10 pin on the ECU side.

So, if you disconnect the T60 connector from the ECU and the T5q connector from the intake manifold control unit, than you can check for continuity the wiring between the ECU and the intake manifold control unit.

Diagnostic part:

Testing the signals from the ECU:

Check if reference voltage +5V are coming from the ECU with a voltmeter between pin 1 and 3 on the T5q connector.

Check with scope between pin 4 and 5 is there a signal of 12V or a PWM signal from the ECU for a short time ( around 5sec ) until somebody turn on the car but not crank.

Testing the hall sensor part:

Connect to pin 1 +5V and to pin 3 GND.

Connect a voltmeter positive lead to pin 2 and the negative lead to pin 3.

When the adjustment arm is in a zero position, you should read a voltage

around 0.4v. If this condition is under that voltage you will get an error code of

” P2015 – intake manifold damper sensor, implausible signal ”

If you move by finger the adjustment arm to the max end position, than you should read a voltage around 4.5-5V. If this condition is over that voltage then you will got also the same error code as mentioned before.

If you measure continues the voltage until the adjustment arm is moving, you should get a rising or falling voltage between 0.4 – 5V it depend in which way is the adjustment arm moved. If you don’t have this kind of reading then you have a hall sensor problem.

Testing the motor:

This  motor is a DC 12V brushless motor, and the terminals are directly connected to the ECU and have nothing to do with the hall sensor electronic, I decided to directly power from my lab power source.

My setup on the lab power source was U=12v @ Imax=1.5A.

The adjustment arm should start moving, if no movement or some squeeze noise, over current shown on the power supply, no current consumption than you have a motor failure.

Of course there could be some broken parts also the reason for a non working air inlet control unit.

The problem and how I solved this unit:

The problem in this unit was a miss calibration of the mechanical parts.

Let’s check in the picture what was happened:

fix-air-intake-control-unit

The green arrows show the rotation direction of the mechanism.

how-to-fix-air-intake-control-unit

On this picture the zero point is reached, but the stopping wings are out of calibration. Now the reading on the DMM is 0.25v because the corrupted distance. Check the next zoomed picture left. Also the problem on the other wing too. I think this weak point is made by the manufacturer because of the commercial nature.

The major problem is the 0.25v. This is an out of range signal and the ECU won’t initialize the whole unit. The ECU will set an error. If we go around somehow solving this corrupted distance and bringing the unit back to a reasonable position, where the initial voltage is not under 0.4v then we are in the race again.

Here is how I solved this and I got some “extra features too” 

fixing-flap-adjuster

–              Drilled a hole with a 2.5mm drill.

–              Made a screw thread for the M3 bolt.

Now I physically corrected the moving path of the adjustment arm. With this bolt I can fine tune the correct position of the adjustment arm until it reach the 0.4v.

After this repair, I also made a software calibration of the air inlet control unit  through my diagnostic tool and deleted the P2015 error from the car ECU.

The unit was put on the car and the car is on a test drive around 3 – 4 days without any problems and no error message comes on the vehicle dashboard any more.

fix-flap-adjuster-control-unit

Ok, this warning should maybe be on the beginning but I assume people read stuff before they do stuff. This is my way how I do stuff. So, what I found inside the unit when I lift the black cover was lot of dust. That dust is actually from the plastic parts inside the unit.

Let’s check what type of dust is it:

On this gear is written “PPA-GF30+15%PTFE”

This means:

PPA – Polyphthalamide, some sort of nylon

GF30 – Glass filled 30%

PTFE – Polytetrafluoroethylene is actually Teflon ( added 15% )

I assume this combination of dust is dangerous for human lungs. But! This information gives as another valuable info. Let’s say, we wish to glue together some material with this gear, then we have to use a glue who can glue PPA+G+PTFE and the other material let’s say iron Fe.

I hope you enjoy this tutorial and will save lot of repair time.

 

christian

This article was prepared for you by Christian Robert Adzic from Novi Knezevac-Serbia.




Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-  If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You can check his previous post in the below link:

https://jestineyong.com/throttle-body-diagnostic-and-repair-guide-for-part-number-03l-128-063-b-v110/

 

Likes(89)Dislikes(0)

10 Comments

  1. Mark

    January 7, 2017 at 6:34 pm

    Hey Christian,
    Thanks for a well explained diagnostic path. I quite often come across repairs in the automotive industry where modifications are required. You have done well to give this intake manifold flap another lease on life. The ECU parameters can be very specific and any readings outside will log a code. I read today that it has been suggested that technology in the automotive industry changes on average every 26 seconds - no wonder it is so hard to keep up!
    Keep the articles coming!

    Likes(1)Dislikes(0)
  2. Albert van Bemmelen

    January 7, 2017 at 7:42 pm

    Thanks for the article and the warning Christian! The substance perfluorooctanoic acid (PFOA) is many years used to make Teflon. In the USA known as 'C8' (its moleculair form) and is purely one of most man made toxic chemical. It didn't exist in nature previously. And it now is traceable in everyones blood circulation and causes infertility, colitis ulcerosa, and high blood pressure, all sorts of cancer amongst other effects. DuPont has created one of the biggest environmental scandals like in the Netherlands (Dordrecht near Rotterdam). See: https://www.ftm.nl/artikelen/hoe-dupont-met-teflon-een-ongekende-milieuramp-veroorzaakte
    And it started in the USA 3500 civil cases about this very toxic substance.
    So another bad thing for humanity. And it makes me wonder if I still should use my teflon frying pan?

    Likes(6)Dislikes(0)
  3. Robert Calk

    January 7, 2017 at 11:05 pm

    Nice job, Chris. Thanks for sharing the repair with us.

    Likes(1)Dislikes(0)
  4. PARASURAMAN

    January 8, 2017 at 7:32 am

    Vow! A greatly useful and informative article! Brainy interventional solution also! Hat's off! But I prefer to keep away from automotive electronic Servicing!

    Likes(0)Dislikes(0)
  5. moshe

    January 10, 2017 at 8:24 pm

    F A S C I N A T I N G!!! Nice...thanks for sharing.
    Now, WHERE did you find all the information on what the readings are supposed to be?

    Presumably the vehicle has been travelling around a while so any ideas on why it suddenly lost its calibration?

    Likes(0)Dislikes(0)
    • Chris

      January 22, 2017 at 10:23 pm

      Thanks Moshe for your supporting of my article.
      The informations in this article and all my articles are based
      from original technical documentations what I buy or some of my
      friends bought and share with me, I also use my long year of
      experience in different type of fields of electronics
      from high-tech IT forensics stuff to aircraft electronic to modern
      vehicle technology etc.
      My other resource from where I get info's are people as all you here,
      people who wish to share their experiences with other, no matter young or old.

      My best regards.

      Likes(1)Dislikes(0)
  6. Xavier

    January 10, 2017 at 11:38 pm

    A great piece on diagnostics and repair of air flap control. As mentioned in the introduction most mechanics will suggest to throw it and replace a new unit. Thank you for sharing.

    Likes(0)Dislikes(0)
  7. Yogesh Panchal

    January 13, 2017 at 9:48 pm

    Thanks for informative article.

    Likes(0)Dislikes(0)
  8. Humberto

    January 13, 2017 at 11:51 pm

    Hi Chris, nice job and thanks for sharing your experiencies with us.

    Likes(0)Dislikes(0)
  9. ombra32

    February 6, 2017 at 4:47 am

    Very interesting!
    Congratulations on a job well done!

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close