Replacing Motherboard In Philips DVP3068/94

By on February 26, 2018
dvd player repair

 

 

 

 

 

 

 

 

dvd player repair

This DVD player made the second visit to my workshop (after a gap of one year) with the complaint that it stops after playing for some time. This had visited me during July, 2016 with the complaint of ‘NO DISK’, and I had written an article on it earlier. That time, apart from solving the problem, I had also done preventive maintenance service.  But as mentioned earlier, this DVD player is being used continuously for hours together by the customer for reasons already explained. (http://jestineyong.com/no-disc-error-dvd-player/)




When I checked, I found that it was intermittently working and stopping when it worked. Checked the voltages on PS Board and found these to be – 8 and + 5 exactly even on load. So that section was ruled out.  I noticed that uController was getting extremely hot and one resistor was burnt in the main board. So, I removed it and found that the bottom of the uController IC was dark!

how to repair dvd

Checked and found that there were no other defective components in the power supply section and ESRs of all caps were within the limit. Hence there was no other go, but to replace the mother board, as getting a replacement of uController was not available in the market and moreover, I am not yet fully confident of replacing the IC with its hundreds of tiny pins! It was rather a ‘spidery’ scare for me!

The mother board that we get readily from the market is a general board that unfortunately will not interface with the front control panel. It will work only from the remote. I connected a universal mother board with a new SMPS which has +5V and -12V required by the mother board.  The SMPS of Philips had only +5V and -8V.  So, I could not use that. Took two two-pin connectors from my stock and directly soldered the other ends to Power Supply Board. Interchanged the connections of Tray for sliding motor, loading motor and spindle motor by sliding out the metal sockets from the connectors, to suit the connections on the new board, as these were different from Philips mother board.  (Since I had already covered about such connections and mother board change in my previous articles, I am not repeating these here). Interchanged the connections of USB connector and made it matching. Did the same for control panel, to enable IR detection and Power LED.

how to fix dvd player

Since the universal mother board needs an ‘end’  (or starting position) switch feedback from the interface with the tray, and these were not there in the Philips original mother board, the need to fix a ‘push to on’ switch arouse again. Unlike last time, when I fixed a salvaged leaf switch, I used a small button switch and after experimenting the movement and studying the position, fixed it like before, wiring it to the two vacant pins on the connector PCB:

how to fix and repair dvd

Connected the boards and tray after rechecking everything and power it on. It worked, but it was not taking all CDs, especially DVDs, showing either ‘disk error’, ejection or continuously spinning without any indication. The laser light was present in the Eye unit. But I could play only a few CDS.    This is an indication that the eye unit has become weaker.  So, replaced it with a new one.  This eye unit has a peculiar cutting for the sliding gear that moves the eye across the CD.

eye unit in dvd

After that I played the CDs and found that with the new eye unit, though more number of CDs were getting accepted, it was not playing DVDs and certain CDs. So, adjusted the gap of the spindle platter (slightly increased the gap between the motor and platter).  It then worked very well. This is important. The focal length of eye unit may not be the same that of the one which was working earlier. So, we need to adjust it on trial and error method.  Now the DVD player was working very well taking up almost 26 DVDs/CDs I tried.

dvd player repaired

Since the arrangement of RC sockets behind the mother board were different from that of the Philips Mother Board, I plucked the RC sockets from the defective board and fixed it at the rear panel and wired these to the mother board externally.

dvd player output jack

You will notice from the above picture that the Video out was at the bottom left, but in the new board, it was reverse and it had some other connector also under the Video out. That is why I resorted to this transplant! Having seen how the IC got burnt in the previous board. I fixed a mini cooling fan, wiring +12V to the SMPS (This is not used by the mother board and was free) and placed it near the IC for cooling it. (Sorry, forgot to click all these!)




Closed the covers and allowed it to run for many hours continuously, playing one CD after another and intermittently trying USB too. It worked very well without any problem!

fixing dvd player

So, another job finished to my utmost satisfaction! (Customer took delivery a few days back and reported that her son was very happy to have the player working, listening to his favorite songs!)

This article was prepared for you by Parasuraman Subramanian from India. He is 68 years old and has more than 30 years’ experience in handling antique equipment like Valve Radio, Amps, Reel Tape Recorders and currently studying latest tech-classes conducted by Kerala State Electronics Technicians’ Association. He has done graduation in BBA degree, private diploma in Radio Engineering and retired as MD of a USA company. Presently working as Consultant to Hospital and other institutions.




Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

You may check on his previous repair article below:

http://jestineyong.com/servicing-romai-power-bank-10400mah/

 

 

Likes(57)Dislikes(0)

15 Comments

  1. R Murali

    February 26, 2018 at 9:54 pm

    Great job. Thsanks for sharing...

    Likes(2)Dislikes(0)
  2. George Greenfield

    February 26, 2018 at 10:04 pm

    Wow I am impressed. I Never even consider a main board transplant. Great Job Parasuraman !

    George

    Likes(3)Dislikes(0)
  3. Yogesh Panchal

    February 27, 2018 at 12:54 am

    Good job! sir

    Likes(2)Dislikes(0)
  4. Suranga Electronics

    February 27, 2018 at 1:35 am

    Hi.. Mr. Parasuraman .
    Very Good installing job.

    Likes(2)Dislikes(0)
  5. Albert van Bemmelen

    February 27, 2018 at 1:58 am

    Great repair Parasuraman and something many engineers would fail to repeat!
    Replacing the player by another Laser head unit is something I only did on a Sony Playstation 2. But in my case that Laser head was a new identical Sony unit. But it also involved adjusting the head afterwards so that both Games and Movie Discs each still would successfully play.
    I never replaced a dvdplayer mainboard because it mainly were the dvdplayer Trays that needed replacements. Like in the XBOX or my dvd player recorder(s). Sadly the often used dvd player trays use different flat or flexcable connections which make replacing them almost impossible, and a new replacement mainboard needs to have those same connectors.

    Likes(3)Dislikes(0)
    • Parasuraman

      February 27, 2018 at 11:27 am

      If the sizes of the connectors are same, we can carefully slide out the connecting pins from its socket by pressing down the locking pin with a needle. Then reinsert it in proper place matching the mother board. I have done that many times. If the size of the connector does not match, slide out all the pins and reinsert it on a suitable blank connector picked up from junk or bought.

      Likes(1)Dislikes(0)
  6. Mihai

    February 27, 2018 at 2:48 am

    Great job sir !

    Likes(2)Dislikes(0)
  7. AGUSON CHYCO

    February 27, 2018 at 3:44 am

    Waoo very interested and marvelous practical,sir can I replace the MB of VC to the DVD device?

    Likes(2)Dislikes(0)
    • Parasuraman

      February 27, 2018 at 11:22 am

      What's VC?

      Likes(0)Dislikes(0)
  8. Robert Calk

    February 27, 2018 at 12:14 pm

    Great job Parasuraman.

    Likes(1)Dislikes(0)
  9. SHIVAKUMAR K

    February 27, 2018 at 2:44 pm

    Dear Sir,

    Great Job, your articles are very clear & your explaining step by step. very easy to fresher like me. Thanks for sharing the airticle. Because I have a DVD player with same mother board problem. this article was helped me.

    Thanks and regards
    Shiva

    Likes(1)Dislikes(0)
  10. James

    February 27, 2018 at 4:08 pm

    The Master at play'. 🙂

    Likes(1)Dislikes(0)
  11. abigail karonga

    February 28, 2018 at 5:33 am

    Excellent repair and good step by step guide easy to follow up with clear pictures

    Likes(1)Dislikes(0)
  12. Tom Struthers

    March 1, 2018 at 3:56 am

    I really enjoy your articles. They are so thorough and informative. Makes me realize how little I know.

    Likes(1)Dislikes(0)
  13. Debirt Maynard

    March 14, 2018 at 8:20 am

    I am impressed. This is a thinking out of the box repair. worth replicating.

    Likes(1)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *