Don't Miss

Standby Problem In Haier LCD TV Repaired

By on August 7, 2017
how to fix haier tv

 

 

 

 

 

 

Haier LCD TV STANDBY REPAIR

A customer sent to me this 24″ Haier LCD TV for repair with the complaint of red standby light on with no picture.  The usual standby problems are :

  1. DC output supply from SMPS fluctuates or lower than normal (due to bad filter capacitors)
  2. Bad SMD voltage regulator IC in the mainboard- produce a lower than normal voltage
  3. Corrupted data in Mirocontroller, Flash Rom or even EEprom IC




Once the cover was removed I can clearly see two circuit boards. It was the power supply and mainboard-see the photos below:

standby problem in lcd tv

how to repair standby problem in lcd tv

I’m a bit happy to see that there were several bulged filter capacitors. This could  be the reason why the LCD TV went into standby mode because the Microcontroller IC did not get a steady dc voltage input.




If the filter capacitors were good then I may need to put some extra effort to look for the data for the memory ICs. For your information it was not an easy task to find original data/programs for the memory ICs.

standby problem fix

how to fix standby tv problem

After replacement of five electrolytic capacitors, the LCD TV came back to life and you can see the photo  below:

how to repair haier tv

If you wish to learn how to repair LCD, LED or even OLED TV, I suggest that you check out on Kent’s website here.

suranga

This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.




Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

Note: You may check out his previous post in the below link:

https://jestineyong.com/7n65c-power-fet-shorted-in-singer-hi-fi-dvd/

P.S-  If you enjoyed reading the above article, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Likes(123)Dislikes(1)

10 Comments

  1. Angelo

    August 7, 2017 at 12:19 pm

    Thanx sir
    quite easy n time saving article...
    Straight to the point

    Likes(4)Dislikes(1)
  2. Albert

    August 7, 2017 at 3:39 pm

    Pro job Suranga, thanks! Knowing how many times e-caps are bulged we maybe should make a list of what manufacturer made them? It is known that there was a problem with the chemical e-cap electrolyte substance in the past. But that was already years ago after they said that an employee took off with the right formula and many bad e-caps were produced afterwards. It would be interesting to know what chemicals they exactly use nowadays. Also because it is said they contain unhealthy carcinogenic chemicals. And if it was not a too high DC voltage, it maybe was the bad electrolyte that made them bulge?

    Likes(5)Dislikes(0)
  3. Parasuraman

    August 7, 2017 at 4:13 pm

    Very easy solution, lucky too!

    Likes(3)Dislikes(0)
  4. Moniem

    August 8, 2017 at 11:20 am

    Good job sir

    Likes(2)Dislikes(0)
  5. Ulises Aguilar Pazzani

    August 8, 2017 at 12:00 pm

    Mr Suranga Bandara, great fix Sir

    Likes(2)Dislikes(0)
  6. Yogesh Panchal

    August 8, 2017 at 10:44 pm

    Good Job! Suranga.

    Likes(1)Dislikes(0)
  7. Charles

    August 11, 2017 at 3:46 am

    Thanks for clarity in your article sir that is very helpfull well done on your good repair

    Likes(0)Dislikes(0)
  8. Humberto

    August 12, 2017 at 12:20 pm

    Good job Suranga.

    Likes(0)Dislikes(0)
  9. john

    August 15, 2017 at 12:34 pm

    74cm CRT show h line already checked all power supply all good 34v present to vertical ic.an i changed it to new one as well as main ic 8895.but problem remain.hout 130v present an test good.what could problem its teledex.

    Likes(1)Dislikes(0)
  10. joku

    August 23, 2017 at 11:29 am

    i have the problem for tv lcd/led haier. the problem is when the plug on to source voltage indicator lamp red on and when klik the power swicth blue lamp on and few minute back to red. please give me any solution thanks.

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close