Don't Miss

Accuracy, Precision and Resolution

By on November 13, 2015
test meter accuracy

 

 

 

 

 

 

 

While reviewing and polishing my notes for another training course in Electrical/Electronic Measurements I thought I could share this important chapter.

Because the terms Accuracy, Precision and Resolution are too often confused I spent more time on this chapter than on any of the others, trying to make it as clear as possible.  Here it is, hoping you enjoy the ride:

accuracy of multimeter

Accuracy

The accuracy of a measurement is nothing else than the difference between the measured value and the true value. Often it is indicated as a plus or minus a percentage of the readings or percentage of the full scale for a selected range. This parameter is specified for every measuring device in relation to the equipment errors only. Sometimes it might also specify some environmental conditions such as temperature, humidity etc…

Examples of accuracy specification:

+/- 1% of measured value

+/- 1% of full scale

Notice the difference between the two examples above. We will talk about this later.

Thus accuracy is not ambiguous. It just tells you how far you are from the goal! The figure below shows the accuracy of a measurement in relation to the full scale of the meter.

full scale meter

Precision

Precision is too often confused with Accuracy and many consider those two words as synonyms. However, precision has absolutely nothing to do with accuracy, except maybe that an accurate instrument is often precise as well (technology obliges!). Precision is the average value of a set of readings, taken repeatedly with the same measuring device in the same conditions. The deviation of the readings from the mean (average) value determines the precision of the instrument. The figure below illustrates this:

precision in meter

A measurement system can be accurate but not precise, precise but not accurate, neither, or both. The figure below better illustrates those differences:

4

Resolution

The resolution is the smallest change in input that the instrument can display for a particular range. Resolution is also often confused with accuracy but has nothing to do with it. Resolution is defined differently for analogue and digital meters, so we will discuss this separately for both types of instruments.

Now it’s time to see how these concepts apply to our measuring instruments:

Digital Meters

Digital multi-meters are now far more common but analogue multi-meters are still preferred in some cases; for example when monitoring a rapidly varying value. We will talk about analogue multi-meters later in this article.

Digital multi-meters (DMM, DVOM) display the measured value in numerals. Each numeral with possible values from 0 to 9 is called a digit.

The first digit on the display is called the Most Significant Digit (MSD).

The last digit on the display is called the Least Significant Digit (LSD).

lsd in meter

Digital meters are specified by the maximum number of digits they can display. It often consists of a number of full digits (each of them can display any number from 0 to 9) plus one fractional digit (1/2, 3/4, 4/5 etc…). This fractional digit is what often leads to confusion. It is a digit that can only display a few numbers (0 to 1 or 0 to 3 etc…). Usually the rule is as follows:

Fractional digit = a/b

a = maximum value the digit can attain

b= number of possible conditions

 

Examples:

½ = from 0 to 1 (max value = 1 with 2 possible conditions, 0 and 1)

3/4 = from 0 to 3 (max value = 3 with 4 possible conditions, 0, 1, 2 or 3)

4/5 = from 0 to 4 (max value = 4 with 5 possible conditions, 0, 1, 2, 3 or 4)

fractional digit in meter

Unfortunately, some manufacturers do not follow this rule, leading to confusion… For that reason some manufacturers introduced another way of looking at the number of digits, the number of counts.

Counts

To avoid the possible confusion due to wrong interpretation of the fractional digit, manufacturers also provide the number of counts for a given instrument. This is exactly the same information as the number of digits but much easier to understand:

The number of counts represents the maximum number the meter can display +1 (ignoring the decimal point). For example a 3 ½ digit meter can display a number as big as 1999 so it will be rated 2,000 counts (1999 +1).

You may wonder why the +1… Many seem to believe that it is just to make it looking better (this is what I found from my intensive research using Google!). The reality is much simpler: because it starts counting from zero, there are 2000 possible numbers (counts) on a 0000 to 1999 display!

meter counts

Digital Meter Resolution

People usually talk about a digital meter’s resolution in number of digits. You will find advertisings that says “This meter has a 3 ½ digit resolution” or “Meter Resolution: 3 ¾ digit” etc… It is not totally wrong but it is not totally correct either. Here is the official definition:

8

For example, a 20,000 counts meter (4 ½ digit) on its 100 V range will display up to 100.00V. The smallest value it can display on that range would be 0.01V. This is the resolution for this range. The same meter on the 10 V range will display 10.000 V. So its resolution for this range would be 0.001 V (the smallest value it can display on that range).

In reality the resolution is a function of the number of full digits. A 3 ¾ digit meter has the same resolution as a 3 ¼ digit meter as shown in the examples below.

  1. A 3½ digit DMM’s (2,000 counts) maximum display on the 2 V range is 1.999V, with 1 mV (0.001 V) resolution.
  2. A 3¾ digit DMM (4,000 counts) on the 4-V range can measure up to 3.999V, also with 1 mV (0.001 V) resolution

Both the 3½ digit and 3¾ digit meters offer 1 mV resolution, even though the 3¾-digit meter has twice the range of counts!

Sounds complicated? Just think about the smallest value the LSD can display for each range and you have the resolution.

Digital Meter Accuracy

To start with, let’s have a look at the accuracy table of a Fluke Model 87 (4 ½ digits):

digital meter accuracy

The table also includes the resolution for various ranges. Please note that it corresponds to the smallest value the LSD can display for each range as explained in the previous chapter.

What about the accuracy? Here you can see that it is also specified for each range, although in this case they are all the same: +/- (0.05% + 1) – except for the mV range. But this is not necessarily the case for all the meters! Most meters will have different values of accuracy for each range. For example here is the DC Voltage Accuracy table of the Brymen BM867s (4 4/5 digits 50,000 counts):

50,000 counts meter

Now what is this “+1” or “+2d”, “+3d” etc… that you find in every analogue meter accuracy specifications? It means that we have to add the value of 1 or 2 or more “digits” to the accuracy of the reading. Confusing? Yes indeed it is! The word “digits” is very unfortunate in this case, it would be much better to use the word “LSD counts”. What you have to add to the percentage of the reading value is a number of counts of the Least Significant Digit for this range. Here below are two examples:

digital meters accuracy

Analog Meter Resolution

Resolution is not often mentioned in Analogue multi-meters specifications. At least I couldn’t find any specification amongst the various models I surveyed. It is probably because we can find the resolution by looking at the scale divisions…

The resolution of an analog meter corresponds to the smallest scale subdivision for a particular range.

analogue meter accuracy

The resolution of the instrument above is 0.1 V for the 6VDC range, 0.2 V for the 12VDC range and 0.5V for the 30VDC range.

Analog Meter Accuracy

Analogue meters usually have their accuracy listed as a percentage of the full-scale reading. Let’s have a look at some real data. This is from a Tenma 72-8170:

tenma-728710

As mentioned above, the accuracy is given as a % of full scale. Let’s see two examples:

On the 12 VDC scale the accuracy is +/- 3% of full scale (12V) = +/- 0.36 V

If you measure 10 V on this scale, the accuracy of your measurement will be:

+- (0.36/10) * 100 = +- 3.6 %

If you measure 5 V on the same scale, the accuracy will be:

+ – (0.36/5) * 100 = +- 7.2 %

That’s why measurements using analogue meters are more accurate when the pointer is closer to the full scale, at least ¾ of the full scale.

Sensitivity

Sensitivity is an absolute quantity, the smallest absolute amount of change that can be detected by a measurement. Please note that sensitivity should not be confused with resolution which is the smallest change in input that the instrument can display for a given range. Usually the sensitivity is a lower value than the smallest range resolution. Otherwise the LSD for this range would be meaningless… Digital instruments are very sensitive, sometimes too sensitive indeed. This is one of the reasons why we prefer using analogue instruments in some specific situations.

Sensitivity however is one of the most important characteristic of analogue multi-meters. This is because the meter must draw a certain amount of current from the circuit it is measuring in order for the pointer to deflect. The less current, the more sensitive the instrument is. The meter appears as another resistor placed between the points being measured. This characteristic is specified in terms of a certain number of Ohms per Volt (or Kilo-Ohms per Volt). The Ohm/Volt figure allows us to calculate the effective resistance for any given range. Just by multiplying this value by the range.

For example a multi-meter having a sensitivity of 20 KOhm/V will have a resistance of 200 KOhm on its 10 V range, or 2 MOhm on its 100V range etc…

The sensitivity for AC and DC is usually printed on the meter scale.

meter scale accuracy

On the meter above we can see that the 50 uA and 0.1V DC scales are only one. What happen if we divide 0.1V by 50 uA? The result will be a resistance of 0.1/0.000050 = 2000 Ohm= 2 KOhm.

2 KOhm on a measuring range of 0.1 V = 20 KOhm/V… not surprisingly!

When making measurements the resistance of the meter should be at the very least ten times the resistance of the circuit being measured.

Conclusions

Multi-meters, digital and analogue, are the most important instruments in a repair workshop and there is a lot to gain in understanding their specifications. Any serious electronic technician/engineer will have more than one multi-meter so he/she can compare the measured values in case of any doubt.

Multi-meters must be checked for accuracy in a regular basis. There is no need to go to a professional lab for this. You can get a voltage/current reference as suggested by Robert (https://www.jestineyong.com/how-to-check-the-accuracy-of-your-meter/). Alternatively you can build your own voltage reference. There are many good articles and schematics on the Internet, such as this one: http://www.frankshospitalworkshop.com/electronics/diy-voltage_reference.html. This might be a project for the next rainy weekend?




Now you should not be paranoiac about it either. If you measure 4.85V at the output of a 5V power supply it doesn’t mean that the Power Supply is faulty!  But it is nice to know if it is the voltage that is a bit low or your meter that needs calibration… On another hand, if you measure a point labeled “3.1 V +- 20 mV” in the service manual then you need to know if you can trust your multi-meter.

Knowing your meters and how to interpret the results is the key.

geraldmusy

 

 

 

Penang,

Gerald Musy

Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-  If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

You may check out his other article below:

https://www.jestineyong.com/which-resistor-to-use-with-this-led/

 

Likes(124)Dislikes(0)

38 Comments

  1. Stanley

    November 13, 2015 at 1:24 pm

    Wonderful article. Thank you very much for this, God bless.

    Likes(2)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:22 pm

      Thank you for your support Stanley.

      Likes(0)Dislikes(0)
  2. Maged Mohamed

    November 13, 2015 at 1:32 pm

    Thanks very much for a great article

    Likes(1)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:23 pm

      Thanks for your support Maged.

      Likes(0)Dislikes(0)
  3. Muftah

    November 13, 2015 at 3:01 pm

    Hi Gerald ,
    Thanks for collecting and sharing this good article.i get confused about these words sometime.
    best regards

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:27 pm

      Thanks Muftah. We all get confused, that why I try to make it as clear as possible. But it is not always easy, you will find a lot of contradictory information on the net. Cheers, GM

      Likes(1)Dislikes(0)
  4. Robert Calk

    November 13, 2015 at 3:08 pm

    Thanks, Gerald. That is a nice lesson on a somewhat confusing topic.
    I recently purchased a Brymen 869s and I like it very much.

    Likes(1)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:35 pm

      Hi Robert, thanks for your support. The Brymen are great instruments. I recently purchased the 867s and really like it. The 869s is even better based on the specs. I would be interested to learn from you how it compares to your Fluke 87V.
      Cheers,
      GM

      Likes(2)Dislikes(0)
      • Robert Calk

        November 15, 2015 at 4:32 am

        Hi Gerald,
        I love the Brymen better than my Fluke, mainly because of the dual display, better resolution, and the 500,000 count mode for DCV. Also the crest feature, PC interface, and other things. The continuity tester is excellent too. A guy on YouTube has a video comparing it to the Fluke - the Brymen won, but he didn't give the Brymen a high transient voltage test. Here is the link if you would like to watch it:
        https://www.youtube.com/watch?v=K-4L2JarVxA
        But I'm glad to have both meters!

        Likes(2)Dislikes(0)
      • Robert Calk

        November 15, 2015 at 6:59 pm

        Hi Gerald,
        I wrote you a comment, but it disappeared. So here it goes again.
        I love my Brymen 869s more than my F87V, so far. It has better resolution, continuity tester and features, including that it has a PC interface. The accuracy is as good or better, or it seems so. I'll have to send in my Voltage Standard and have it recalibrated to be absolutely sure - it was last calibrated 7/14, so it could have drifted a bit. I feel very fortunate to be able to have both of them! You can go to YouTube and type in,"Brymen 869s vs. Fluke 87V".

        Likes(0)Dislikes(0)
        • Robert Calk

          November 17, 2015 at 6:27 pm

          The comment reappeared after I sent this comment. I'm not sure what happened.

          Likes(0)Dislikes(1)
  5. Paris Azis

    November 13, 2015 at 4:04 pm

    Hey Gerald

    Thank you for this excellent article!

    Best Regards

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:39 pm

      Thanks Paris. I also read all your articles and, if no comment, I always put a thumb up. Excellent exchange of information and this makes this site more and more interesting.

      Cheers,
      GM

      Likes(0)Dislikes(0)
  6. Albert van Bemmelen

    November 13, 2015 at 4:18 pm

    Your article is very well expained and tells it all! Thank you Gerald. It also explains why you also are known as the Professor.

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:47 pm

      Thanks Albert 🙂

      Always looking forward to read your articles.

      Cheers,
      GM

      Likes(0)Dislikes(0)
  7. Gerald Millward

    November 13, 2015 at 5:52 pm

    Gerald - excellent refresh for old codgers like me - thank you.

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:54 pm

      Thanks Gerald. I am not young either (68), but I feel young... My teacher always told me to stick to the basics, this is what I am trying to do. Understand your basics and you will understand more complicated topics.

      Cheers.
      GM

      Likes(2)Dislikes(0)
  8. Anthony

    November 13, 2015 at 6:18 pm

    Hi Gerald,
    Thank you for sharing this article, it is very educational and enjoyable to learn from your knowledge.

    Kind Regards

    Likes(1)Dislikes(0)
    • Gerald

      November 14, 2015 at 8:55 pm

      Thanks Anthony, I appreciate your support.

      Cheers,
      GM

      Likes(0)Dislikes(0)
  9. Hank Bordeaux

    November 13, 2015 at 11:48 pm

    Well written but no mention of input impedance (higher the better) 10 meg ohms is standard of a good meter and reflects the loading on a device being measured.

    Likes(1)Dislikes(1)
    • Gerald

      November 14, 2015 at 9:08 pm

      Hi Hank,

      Thanks for your comment and support. Correct about the input impedance, which could be a problem with analogue multi-meters but usually not a problem with digital meters as they normally have a very high input impedance.

      Actually the low input impedance of analogue meters is an advantage in some situations.

      Use of the multi-meters could be the subject of another article.

      Cheers,
      GM

      Likes(0)Dislikes(0)
  10. Pepper

    November 14, 2015 at 1:18 am

    Mr. Musy
    Excellent trip into déjà vu for me. Thanks!
    I distinctly remember our shop getting the Fluke 8020 DMM’s in the late 70’s and what a difference .25% accuracy made!

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 9:10 pm

      Thanks for your support Pepper. Always appreciate your comments.

      Likes(0)Dislikes(0)
  11. gasmel bashir

    November 14, 2015 at 4:04 am

    it is very interesting and useful.

    Likes(0)Dislikes(0)
  12. Henrique Jorge Guimarães Ulbrich - Brazil

    November 14, 2015 at 5:08 am

    Gerald, changing the things a bit, not only the measuring instruments, but what can ve seen is that is just your article that have at the same time Accuracy, Precision and Resolution. Very, very good. Thanks a lot.

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 9:12 pm

      Muito Obrigado Henrique

      For your support and comments.

      Abraços,
      Geraldo

      Likes(0)Dislikes(0)
  13. Manuel-Loto

    November 14, 2015 at 6:49 am

    Excellent article...and good lessons. Thank very much

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 9:14 pm

      Thanks for your support Manuel

      Likes(0)Dislikes(0)
  14. Parasuraman S

    November 14, 2015 at 9:04 am

    Great! What an in depth study on an area otherwise neglected by most of the Technicians! Very informative and helpful! When technicians of varied interests and various exposures, join together in this forum run by the Great Jestine Yong, and share their experience willingly to others, it makes it very unique and very valuable (I should say 'invaluable', but that word, though means 'something that cannot be measured to give a value - rather infinite', is commonly mistook for 'not valuable'! I learnt a lot from this article, though some of it needs revision several times to imbibe! Congratulations and all the best! Pl keep posting such articles!

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 9:16 pm

      Thanks Parasuraman for your support.

      Likes(1)Dislikes(0)
  15. Yogesh Panchal

    November 14, 2015 at 3:38 pm

    Thanks for sharing and refreshing our knowledge.

    Likes(0)Dislikes(0)
    • Gerald

      November 14, 2015 at 9:17 pm

      Thanks for your support Yogesh

      Likes(0)Dislikes(0)
  16. Aziz

    November 15, 2015 at 4:45 am

    Thank you very much for a great article

    Likes(0)Dislikes(1)
  17. Aziz

    November 15, 2015 at 4:56 am

    Hi mr jestine yong, i am sorry for dislikes , in thank you very much for a great article

    Likes(1)Dislikes(0)
  18. Zsolt

    November 15, 2015 at 10:19 pm

    Hello,
    Very, very good, and useful article.
    Many thanks!

    Likes(0)Dislikes(0)
  19. Humberto

    November 17, 2015 at 11:27 pm

    Thanks Gerald for this article, very well explained. I confess that we, the readers learn more and more with your didactical articles. Thanks.

    Likes(0)Dislikes(0)
  20. parshuram

    November 18, 2015 at 12:51 pm

    hi
    very very good and usefully articles
    i have digital microscop for lcd ripping tools

    Likes(0)Dislikes(0)
  21. Ulises Aguilar Pazzani

    November 20, 2015 at 12:07 pm

    Mr Musy very interesting , nice for sharing

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close