Don't Miss

A surround amplifier with no sound output repaired. Model Vtrek AV-3100

By on March 5, 2014
amplifierrepairing

 

 

 

 

 

 

 

 

I got a call from the principle of the Lutheran school in my area to go and check the amplifierin their school theater. When I got there, and powered all the equipment, I could see there was a standby light but there was no sound coming out of the speakers; not even a hiss sound.

amplifier repair

It is an old amplifier but a very good quality one.

amplifier repairs

As you can see, the standby light is on and the panel is on as well.

A few screws were off and the inside board was exposed.

amplifierrepair

The moment I scanned the board with my naked eye, look what I found.

amplifier repairing

That was an obvious sign of some bad transistors. The first thing that came to my mind was what part number is that blown transistor?

amplifier repairings

Here is a close look of the blown transistor. When I got closer with my x10 magnification, I could see that part number of this blown transistor was printed on board. I also found out later on that there was another transistor shorted next to this blown one.  The part numbers are: TIP42C and TIP41C. It was a push pull amplification.

amplifier repaired

If you measure voltage across these transformers, you would get negative and positive readings. I could not find the actual part number so I had to use replacement for them. They were: BD244C and BD243C. After replacing these parts, I looked for more shorted or blown parts and look what I have found.

amplifierrepairs

A 220 ohm resistor, a 2n5401 and 2n5551 transistors were found blown and shorted on the same line of the other transistors were found before.  As you can see in the photo, the part numbers are printed on the board. All these blown and shorted parts were replaced with the same part numbers and when I powered up the device, everything worked nicely.

amplifierrepairings

As you can see, all these parts were replaced on this old but nice amplifier. I forgot to mention that the main fuse (5 amps) was open as well, but I could not locate it to take picture of it simply because it was blown to pieces.

 

 

I took it back to the Lutheran school and installed it back in the theater there and everything worked just fine.  Mission accomplished.

waleed

 

 

 

This article was prepared for you by Waleed Rishmawi, one of our ‘Master Authors’ and currently working in the Bethlehem area of Palestine repairing electrical and electronic equipment.

Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S- Do you know of any your friends who would benefit from this content that you are reading now? If so, forward this website to your friends or you can invite your friends to subscribe to my newsletter for free in this Link.

 

 

Likes(14)Dislikes(0)

5 Comments

  1. mahienn

    September 10, 2015 at 4:55 am

    u simply r a genius sir

    may god bless u...

    mahienn

    Likes(0)Dislikes(0)
  2. mahienn

    September 10, 2015 at 4:58 am

    dear sir

    can i replace a (rgp 02-12)diode with (in 4007)?

    any comments would be appreciated thanx

    Likes(0)Dislikes(0)
  3. Ivan

    June 3, 2020 at 3:50 am

    push pull amplification .talk abt it please

    Likes(0)Dislikes(0)
  4. boyd k

    July 3, 2020 at 10:53 pm

    what makes a tda2030 ic blown whenever I change a new one?

    Likes(0)Dislikes(0)
  5. RAJAIY

    May 24, 2023 at 6:28 pm

    Hi Sir

    I have the same product VTREK AV-3100 in my home, I have a blue light on the top when the power is on, but the front panel has no light so I can't know if working or not as it is not in use for more than 15 years.
    could you tell me what could be the problem?

    thanks

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close