Don't Miss

Assembled A 555 Based Timer For Water Boiler

By on August 4, 2021
water boiler home drawn schematic

 

 

 

 

 

 

 

ASSEMBLED A 555 BASED TIMER FOR WATER BOILER

We have an assembled water boiler in our house. This was made many years back, when I was working in BPL and staying in Bangalore. A stainless steel vessel was fit with a heater and thermostat at the bottom. The minimum temperature has to be set at around 35◦C or more without which the thermostat did not function, which was ok for us for the climate at Bangalore. But when we returned to our native place in Kerala, the climate of which is very humid and warmer, the temperate of minimum 35◦C was too much.

Though I tried using different types of temperature controllers, all of which worked on metal expansion/contraction basis, it was not shutting off and many times, the water reached the boiling stage causing very high electricity consumption and wastage of hot water. That is how I bumped upon the idea of fixing a timer. From my experience, keeping the heater on for about 12-15 minutes was enough to reach the temperature required for our use. So I used the following timer board for assembling a control circuit through a 30A contractor relay, a hand-drawn schematic of which is given below:

control circuit for water boiler

how to fix and repair water boiler control board

I studied the following link in detail and modified the above board to replace the capacitor to 1000/63V and the trim pot to 1 Meg. The rest of the schematic of the 555 Timer shown below will not match with the above board, which is ready to buy type from the open market. (I had stock of these boards which I bought for some other project)

1 Minute, 5 Minute, 10 Minute and 15 Minute Timer Circuit Diagram (electricaltechnology.org)

555 timer diagram

I adjusted the timer to switch on the relay after about 15 minutes, which I did by applying power to the board and adjusting the resistance to about 812K as mentioned in the article. I had to readjust the trim pot after a couple of trials to reach this level. Then next task was to obtain the following parts for assembling the timer:

  1. 30A Contractor – two pole, coil working on 230V AC directly. (The AC inputs are given to L1 and L2 and Load is given to T1 and T2. When the coil gets energised, the connection gets closed between L1 to T1 and L2 to T2)

sibass

  1. Casing for the contractor
  2. Transformer to make power supply for the 12V 555 Timer board. (I used a 7.5V-0-7.5V, 500mA which I had in stock and connected both ends without using the centre tapping. This provided about 15V AC)
  3. Bridge rectifier – 1 No.
  4. 0.01uF/100V caps – 2 Nos.
  5. 2200uF/25V cap – 1 No.
  6. 220uF/25V cap – 1 No.
  7. 7812 regulator IC – 1 No.
  8. Fuse holder with Fuse of 1A (for primary of transformer)
  9. LEDs – 2 (One Red and One multicolor)
  10. IN4007 diodes– 2 Nos.
  11. 1/4W 1 Meg resistor – 2 Nos.
  12. Inter connecting wires.

As the 230V AC coil was drawing only around 59mA current, power consumption even if it was left on was very negligible and further the relay in the timer could take the load very easily:

sibass contractor

First I fixed the contractor in the base of the case I bought for it. Then fixed the transformer on its side. Soldered the ground point of bridge rectifier to the metal case of transformer. Then soldered the two 7.5V AC inputs to it. Soldered the ground point of 2200uF cap to the transformer and positive to the + of bridge rectifier. Soldered 0.01 caps across the two AC in/+ and – points of bridge Rectifier. Then soldered the 7812 regulator heat zinc to the metal case of transformer, which was the ground of it. Connected the + output of the bridge rectifier to the input of 7812. Soldered the 220uF to the output pin of the 7812. Fixed the timer board on the other side of the contractor and wired the 12V power supply. L1 of the contractor was earmarked for Phase (Line) and L2 for Neutral. My requirement was to switch off the circuit after a delay of about 15 minutes. So the coil of the contractor was connected to the NC (normally closed) contact of the timer relay and the other end of the coil was connected to L2 (Neutral). Wired the 230V AC input for the transformer to the L1 and L2 of contractor, through a 1A fuse, holder of which was fixed on the front cover. Then L1 (phase) was wired to the single pole of the Timer relay. The idea was that the coil will remain energized pulling the plunger for closing the contacts between L1 to T1 and L2 to T2, until the relay gets on after the delay, upon which the AC input to contractor will be cut, releasing the plunger. (I am sure many of you might know that the contractor works on solenoid principle.



When the coil is energized the electromagnet pulls the plunger and holds it tight and releases it when cut.) Red LED was fixed on the cover, one side of which was connected to L1 through a 1Meg resistor. The other end was connected to L2 through one IN4007. Did the same for the T1 and T2 also using the colour LED fixed on the cover. The idea was that the colour LED will emit different colours catching the eye when the heater is on. It will go off when the contractor is shut off by the timer. The timer board itself had a red SMD LED that remains lit on power on.  A blue LED will glow when the relay is switched on. This was found useful, as glow from both these SMD LEDs were visible through the case of the Contractor. Now let us take a look on the work done:

contractor sibass wiring

I applied power to the L1 and L2 and tested the unit on my worktable and found it to be working perfectly well, for which I had to leave it on for about 15 minutes. Then fixed the unit on top of the switch board of the heater. Opened the switch board and connected the output (Line and Neutral) of the two pole AC switch to L1 and L2 and connected the heater load to T1 and T2. Unfortunately, the two pole switch broke down and caused a temporary halt to my installation. I had already switched off the power to this line. So, I removed the broken switch and went to market and really hunted for getting an exact replacement, but in vain. So, I had to buy a new switch, size of which was different from what I carried along with a new case, which I fixed on top of the existing switch board. The timer worked very well and water got heated up enough for direct use without a need to mix cold water. I watched its performance like a director watching a trial run after completion of his work. Now we can save electricity and be carefree!

save electricity gadget

Mission accomplished and satisfaction intensified jumped into its collection bag!

This article was prepared for you by Parasuraman Subramanian from India. He is 72 years old and has more than 30 years’ experience in handling antique equipment like Valve Radio, Amps, Reel Tape Recorders and currently studying latest tech-classes conducted by Kerala State Electronics Technicians’ Association. He has done graduation in BBA degree, private diploma in Radio Engineering and retired as MD of a USA company. Presently working as Consultant to Hospital and other institutions.

Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

You may check on his previous article on Dyson Vacuum Cleaner Power Supply Repair

 

Likes(48)Dislikes(0)

11 Comments

  1. Marinko

    August 4, 2021 at 1:24 pm

    Dear sir and colleague, thank you for such an exhaustive description, greetings from Croatia

    Likes(1)Dislikes(0)
    • Parasuraman S

      August 4, 2021 at 2:04 pm

      Many thanks for your comments, dear!

      Likes(1)Dislikes(0)
  2. A van Bemmelen

    August 4, 2021 at 1:57 pm

    Very nice and thought through fix Parasuraman! Question: Does lowering the boiler water temperature not cause the risk of veteran disease also called the lagionaires desease? Which causes longproblems or much worse. Just curious.

    Likes(3)Dislikes(0)
    • Parasuraman S

      August 4, 2021 at 10:00 pm

      Have not even heard of such a disease! Many of us use this type of water and have not faced any problems so far! Shall check what this disease is in website. But ignorance many times is a bliss! Many thanks for your comments, dear!

      Likes(0)Dislikes(0)
  3. Waleed Rishmawi

    August 4, 2021 at 3:20 pm

    very detailed modification with the satisfaction of successful update. thanks for sharing and have a blessed day.

    Likes(1)Dislikes(0)
    • Parasuraman S

      August 4, 2021 at 10:01 pm

      Your comments are always very encouraging, dear! Many thanks for your continued support to this old man! (LOL)

      Likes(0)Dislikes(0)
  4. Yogesh Panchal

    August 7, 2021 at 12:46 am

    Good Modification!Sir.

    Likes(1)Dislikes(0)
    • Parasuraman Subramanian

      August 7, 2021 at 12:58 pm

      Many thanks for your comments!

      Likes(0)Dislikes(0)
  5. P van Beveren

    August 8, 2021 at 6:53 am

    AWESOME knowledge and skill shown

    Likes(1)Dislikes(0)
    • Parasuraman Subramanian

      August 10, 2021 at 5:54 pm

      Many thanks for your comments!

      Likes(0)Dislikes(0)
  6. Parasuraman Subramanian

    August 10, 2021 at 5:55 pm

    Many thanks for your comments!

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close