Don't Miss

AUO 11303 LCD TV T-Con IC Faulty

By on September 2, 2019
auo11303 ic replaced














lcd tv no dsiplay repaired

This Changhong LCD TV came in for repair with the complaint of no picture but have sound. In fact when you look closely at the screen you will be able to see the backlight was lighted. There can be few causes of such problem.

Instead of guessing what might be the cause, I opened the TV cover and checked on the power supply DC output voltages. All DC output voltages were found to be correct.

lcd tv no display repaired and fixed

The next check was on the T-con board IC (AUO -11303) and the cable connection. I reheated the T-con IC and reseated the cable (and cleaned the connector) and the problem turned out to be the same. When I turned the TV On, I could only saw the backlight lighted without any picture-see the three photos below:

how to repair lcd tcon board

how to repair lcd tv no display

backlight have display but no picture

Next step was to replace  the AUO-11303 IC directly and retest it.

auo11303 ic bad

auo11303 ic new

auo11303 ic replaced and fixed lcd tv display problem

After the replacement of the IC, the picture came back-see the photo below:

no display in lcd tv fixed


Conclusion- If the power supply DC output voltages are good then focus on the Tcon board. Check the VCC supply to the Tcon board IC and make sure the IC is not too hot  to be touched and reheat it.

If the problem still not resolved then direct replace the IC and retest it. If after the replacement of the IC and still not be able to repair it, the next step would be to find out the service manual and start checking the important signals pin in the T-con board.


This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.

Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

P.S-  If you enjoyed reading the above article, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check out his previous post in the below links:




  1. Albert van Bemmelen

    September 2, 2019 at 2:26 pm

    Fixing modern TV's is troublesome. They don't have a simple OBD diagnostics scanner like in Cars that have the CAN bus that can point us in the right direction. Although we have the RT809H programmer that we can use, they are quite useless in cases like these where a controller chip is defect. Only a pro can fix these without a service manual at hand!

    • Anand

      August 24, 2023 at 12:10 am

      yes you are right

  2. Yogesh Panchal

    September 2, 2019 at 3:48 pm

    Suranga, Thanks for sharing the article Good job.

  3. Parasuraman S

    September 2, 2019 at 6:09 pm

    Strange coincidence is that I had a similar problem that I could solve with the guidance from my expert friends. Shall post article, when it is made ready. In my case it was CM501 IC, datasheet of which was not available.

    Anyhow, good job, Suranga!

  4. Parasuraman Subramanian

    September 2, 2019 at 9:50 pm

    Any of the readers help me get the datasheet of CM501 and CM601. Please provide a link, if you can or send it to Jestine Yong for forwarding it to me.

    • Albert van Bemmelen

      September 3, 2019 at 5:14 am

      And maybe this PDF helps?

    • Albert van Bemmelen

      September 3, 2019 at 5:17 am

      Or was this the chip you were looking for?

    • Albert van Bemmelen

      September 3, 2019 at 5:29 am

      This is probably the pinconfiguration of the CM501 48 pins smd chip:
      Hope this helps.

    • R Murali

      September 5, 2019 at 12:11 am

      I do read your contributions and happy to gain knowledge from your technical skills . Here is a link for downloading CM501 Data
      For CM601 its Hope this will help you. and Thanks to Mr.Jestine Yong for creating this site........ R Murali

  5. Albert van Bemmelen

    September 3, 2019 at 5:11 am

    Did you see this one Parasuraman?

  6. Waleed Rishmawi

    September 3, 2019 at 1:39 pm

    congratulations on a job well done. I had the same issues with Sanui TV and it was the IC that was causing the problem. sad to say even with new IC's bought off the net, there are a lot of them that are defective but we keep trying till we get it right. keep up the good work my friend and have a blessed day

  7. Idicula

    September 3, 2019 at 10:45 pm

    Actually this not a comment. A doubt.
    I have a Samsung LED TV, Model No. UA32H5500. When switched on some lines are coming vertically or horizontally. Some times up side or down side, left side or right side like that. What are the causes. I am not an expert in LED TV's. Can you help.

    • Parasuraman S

      September 4, 2019 at 7:49 am

      Check the T-con/Scaler Board voltages, like VGH, VGL, VCOM, VDD and AVDD. If these are not normal, check for its supply voltage, usually 12V and its filter caps. If these are all normal, the problem lies in the cof connector and/or panel. That requires expert maneuvering of the X-Y array!

  8. Parasuraman S

    September 3, 2019 at 11:58 pm

    Thanks to all for the links given. I got it for CM501 from a technical group. Can I get the datasheets of CM601 and CM1801B?

  9. jose lopez

    October 9, 2020 at 11:51 am

    tengo una rca 32´´led smart hd tv modelo rtv32z2sm la falla es que se forma doble imagen solo la mitad de la pantalla (parte de abajo) la t-con es la 32t24-cok ctrl que trae los siguientes circuitos AUO p303-19, AUO11311, i7814hp, AUO s302-1v y AUO g301-1v alguien me podria ayudar. soy de Mexico uso el traductor gracias.

    I have an rca 32´´led smart hd tv model rtv32z2sm the fault is that only half of the screen is formed double image (bottom part) the t-con is the 32t24-cok ctrl that brings the following circuits AUO p303-19 , AUO11311, i7814hp, AUO s302-1v and AUO g301-1v someone could help me. I'm from Mexico, I use the translator, thank you.

  10. shantha

    July 4, 2023 at 10:34 pm

    The above IC is too hot, why is that

  11. shantha

    July 4, 2023 at 10:36 pm

    1/2 a display is view


Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.