Comments on: DESKTOP PC AUDIO OUT NOT WORKING REPAIR GUIDE

By: sujoy bhattacherjee

sujoy bhattacherjee — Tue, 22 Sep 2015 16:38:05 +0000

Hi jestine, thank you for your help to teach us to repairing job. thank you foryour coperation sujoy

Likes(1)Dislikes(0)

By: Amir Mukhtar

Amir Mukhtar — Fri, 22 May 2015 09:42:16 +0000

thanks you mr. Christian Robert Adzic to share motherboard repair experience.
Thanks you
However, i do use wrist band to protect electrostatic discharge when repair proceed on digital equipments especially, for Low volt electronic devices except CRT , Power supplies and high Voltage devices.

thanks you
Amir Mukhtar Ashrafi

Likes(0)Dislikes(0)

By: reza

reza — Thu, 21 May 2015 06:27:11 +0000

hi dear Christian Robert
thank u for sharing this article.

Likes(0)Dislikes(0)

By: Chris

Chris — Wed, 20 May 2015 07:05:13 +0000

Edouard Saint-clair:
you alright but in this case pushing out the peace was not possible because of the housing type of the audio jack. To dismounting the audio jack housing on this MB is impossible until you cut the legs which are soldered on the motherboard. After cutting the legs you can strip up the jack housing. No other way on this type of jack. But you fully alright and it is a good advise too of course.

Gopal Sharma:
Removing all the small smd parts are risky because you have to apply more heat to the mobo. With the desoldering gun it is pretty easy and safe.

Thank you all for your comments and for supporting my articles.

Likes(0)Dislikes(0)

By: Humberto

Humberto — Mon, 18 May 2015 15:32:41 +0000

Good job, it's a risky one, but finally the MB was saved from the dump. Congratulations

Likes(1)Dislikes(0)

By: Gopal Sharma

Gopal Sharma — Mon, 18 May 2015 06:38:47 +0000

Good job Mr. Christian Robert Adzic. I had also replaced audio jack and VGA port form one motherboard successfully. But replacing audio jack is very risky as there are few smd components placed nearby may fall off the board. It is better to remove nearby smd components first then replace the jack. It will be safe.

Likes(0)Dislikes(0)

By: Edouard Saint-clair

Edouard Saint-clair — Sun, 17 May 2015 22:46:21 +0000

Hello Christian! How are you? I rather believe that the whole desoldering and removing of the part was probably too hard compared to pushing the obstructing piece out in a reverse way. The fact is, we can get access to the opposite side of the port case, unlatch the cover and, by means of a pointy, long and skinny tool, manage to push back the masking object. Anyway, I really appreciate your valuable posts and references, which I find to be very helpful. Keep up the good work!

Likes(1)Dislikes(0)

By: Ferdinand

Ferdinand — Sun, 17 May 2015 14:54:24 +0000

Thanks a lot Christian for a kind sharing to us...God bless.

Likes(0)Dislikes(0)

By: Robert Calk

Robert Calk — Sun, 17 May 2015 11:54:56 +0000

In reply to Anwar Shiekh.

That's true, Anwar. The way I did it was to use my de-soldering gun to suck up the excess solder, then I used my Hot Air Rework Station to get the USB connector free. That is the best way that I have found.

Likes(1)Dislikes(0)

By: Yogesh Panchal

Yogesh Panchal — Sun, 17 May 2015 07:16:34 +0000

Good attempt on repair thanks for sharing.

Likes(0)Dislikes(0)