Don't Miss

Firmware Issue In Mitsubishi LCD Monitor

By on April 20, 2019
Firmware Issue In Mitsubishi LCD Monitor

 

 

 

 

 

 

 

 

 

Firmware Issue In Mitsubishi LCD Monitor

This Mitsubishi LCD Monitor came in with the compliant of  no power. Once I had confirmed that the Monitor was no power I opened the casing to check to start troubleshooting it.




Below is the photo that shows the Main board, Power supply, and Inverter board section.

eeprom fault in lcd monitor

When I check on the output voltage from the power supply it did showed 5 volt which means the power supply was working. One thing for sure was if all the memory ICs were getting the 5 volt and the front power LED still would not light up means the data in the IC could have been corrupted.

5 volt in mainboard

The easiest  thing to do among all the memory ICs was to reprogram the EEprom IC first before go to Flash Rom and the MCU IC.




I took out the 24C02 EEprom IC and reprogramed it with new data since I got the original data from another similar working set.

eeprom programmer 24c02

Once programmed and powered On, the front power LED was lighted up and I could see the screen appeared (Windows). See the two photos below:

green led in lcd monitor

how to fix and repair lcd monitor

Conclusion- In this case, it was simple to troubleshoot because you already eliminated the power supply cause because it was supplying the 5 volt. So the concentration was on the memory ICs. You need a programmer to extract from a good memory IC and then rewrite or overwrite it in the corrupted EEprom IC. If you want to be an expert in LCD Monitor repair you can check out Jestine Yong’s ebook in LCD Monitor repair– Volume 1 ,2 and 3.

suranga

This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.




Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

P.S-  If you enjoyed reading the above article, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check out his previous post in the below links:

https://jestineyong.com/power-blinks-in-lg-led-tv-repaired/

 

 

Likes(65)Dislikes(1)

11 Comments

  1. Gary Gemmell

    April 20, 2019 at 10:40 pm

    What software and eeprom burner are you using Suranga?

    Likes(1)Dislikes(0)
  2. Mihai

    April 21, 2019 at 12:48 am

    Hello, Suranga ! Good job, thank's for sharing !

    Likes(0)Dislikes(0)
  3. Albert van Bemmelen

    April 21, 2019 at 1:50 am

    Programming Bios/firmware always is the best thing to do first which you did.
    The RT809H is a great programmer for that, in both reading and re-writing/flashing of firmware. Although it is autoverifying and very fast I noticed that if we place Bios chips turned 180 degrees wrong in the RT809H socket, chips are still recognized and read but is followed by a screenmessage saying that there is a verify error at address 000000. (sadly the screen example of the programmer software program how to place in the chip is very tiny and almost impossible to see, so that mistake is easily made).
    Today my programmer luckily fixed another firmware problem with a dead Asus P5KPL-AM SE motherboard that showed no video output and was useless until I re-programmed the sop8 25X80AV Winbond Bios chip with Bios version 0702. A diagnostic card inserted in the mainboard PCI slot showed a running clk signal and a post end code of 32. Which turned out being caused by a corrupt Bios chip. Which easily happens when the Asus mainboard apparently flashes unexpectedly its own firmware (every Asus mainboard is included with an EZflash utility and the EZflash program that is able to fix dead mainboards causing more problems instead of solving them) while a windows installation was started from a iso image on USB memory stick.

    Likes(4)Dislikes(0)
    • Albert van Bemmelen

      April 24, 2019 at 4:39 am

      Luckily it apparently is also possible to ZOOM-IN on the example picture on the left in the RT809H programmer window on how to place any chosen IC. In case of the mentioned Winbond 25X80 eeprom it shows pin 1 in the up to the left direction and pin 8 up to the right in the lowest position of the socket. (Furtest from the sockethandle on the upper left),

      Likes(1)Dislikes(0)
  4. Robert Calk Jr.

    April 21, 2019 at 2:57 am

    Good job, Suranga!

    Likes(2)Dislikes(0)
  5. Parasuraman Subramanian

    April 21, 2019 at 6:29 am

    Expert quick solution as usual! Well done!

    Likes(1)Dislikes(0)
  6. Yogesh Panchal

    April 22, 2019 at 3:51 pm

    Excellent!!

    Likes(0)Dislikes(0)
  7. Andre Gopee

    April 23, 2019 at 11:23 pm

    Great Job. I have a 55 Inch 3D Toshiba that has the same problem and I can get the firmware. I have a programmer but I need the firmware. The model of the TV is 55TL515U. Does anyone have this firmware that I can get or know where I can get it. Thank for the interesting article.

    Likes(0)Dislikes(0)
  8. Devon Wilson

    April 24, 2019 at 5:48 am

    Great job. Thanks for sharing this information with us.

    Likes(0)Dislikes(0)
  9. Bufford Moore

    April 24, 2019 at 11:08 am

    Interesting problem and repair, thanks for posting it. Hope you and all those around you are safe

    Likes(0)Dislikes(0)
  10. Doğan

    December 16, 2020 at 5:15 pm

    You are a very good mechanic. You are telling very well. Greetings from Turkey...

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close