Comments on: Fixing Brand New Never Working Nano 3.0 Arduino Modules https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/ Semiconductors, Test Equipments, Circuit Board Troubleshooting, Electronic Repair Courses and Many More! Tue, 05 Sep 2023 17:21:03 +0000 hourly 1 https://wordpress.org/?v=5.4.19 By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-408017 Tue, 05 Sep 2023 17:21:03 +0000 https://jestineyong.com/?p=30923#comment-408017 In reply to Mohamed Kikia.

Glad to hear that you now most likely are also able to fix your not communicating Nano boards too Mohamed!

Likes(0)Dislikes(0)
]]> By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-408016 Tue, 05 Sep 2023 17:16:49 +0000 https://jestineyong.com/?p=30923#comment-408016 In reply to AdamS.

Although I could open a dispute which I almost also did, there afterwards was no need anymore to complain about these in general decent made quality Nano 3.0 ATmega328p 'clone' boards.
Afterall they were easily fixed with the given method and are still sold for a very acceptable price. Especially compared to original sold Arduino boards.

Likes(0)Dislikes(0)
]]> By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407930 Tue, 05 Sep 2023 04:20:06 +0000 https://jestineyong.com/?p=30923#comment-407930 PS: As far I can tell both the ADP-056 and the TL866 ISP amplifier driver boards use a 74HC244 as buffer chip.

Likes(1)Dislikes(0)
]]> By: AdamS https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407855 Mon, 04 Sep 2023 11:29:49 +0000 https://jestineyong.com/?p=30923#comment-407855 The solution was ingenious but I don't know why you would waste your time with a non-working brand new item when you should be demanding a refund and/or replacement!
The more people accept the shoddy, badly made rubbish supplied by AliExpress and similar suppliers, the more they will get away with supplying it, whilst laughing all the way to the bank.

Likes(1)Dislikes(0)
]]> By: Mohamed Kikia https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407851 Mon, 04 Sep 2023 11:07:47 +0000 https://jestineyong.com/?p=30923#comment-407851 Excellent! I have a few nanos which I bought some time ago and have never used. I will more than likely have the same problem. Thanks for the effort put
into explaining the problem and the solution. I do have the TL866 programmer As well as the pick it.

Kind regards

Likes(1)Dislikes(0)
]]> By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407724 Sun, 03 Sep 2023 08:56:15 +0000 https://jestineyong.com/?p=30923#comment-407724 Thanks moshe! I do seem to have written often about programming and flashing stuff which to me is a very interesting and important part of todays modern electronics.
And to be thorough in this respect it is good to know that also the Xgecu/ Minipro or however the TL866II, TL866 with 6 pin ISP connector is named, does have a special amplifier board available. https://nl.aliexpress.com/i/33047996482.html?gatewayAdapt=glo2nld
Although I up to now didn't need it yet. But I suppose I do in case longer wires are used to flash destination boards over longer distances.

Likes(2)Dislikes(0)
]]> By: moshe jacobson https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407684 Sun, 03 Sep 2023 00:38:40 +0000 https://jestineyong.com/?p=30923#comment-407684 Albert...this article is up to your usual superb standard...great stuff!!
Very useful & full of good hints...thanks for sharing & writing.

Likes(2)Dislikes(0)
]]> By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407660 Sat, 02 Sep 2023 18:57:08 +0000 https://jestineyong.com/?p=30923#comment-407660 PS: Because the in the article mentioned GQ-4x4 universal programmer in ICSP mode is limited to only about 20 cm short signal wires at maximum, we need a special adapter to fix that problem. For this the special signal amplifier expansion adapter ADP-56 board is available that can be inserted into the 40 pins socket to buffer and enhance these ICSP signal levels. Like it was sold here on Amazon => https://www.amazon.com/ADP-056-circuit-programming-adapter-GQ-3X/dp/B00HI23S3E
Sadly now sold out on many websites in Europe and only in stock in Hungary from EPROMIROK.HU. Where I recently ordered this special ICSP adapter board so it can be used to program over JTAG, SPI and PIC chip in circuit. Also because ordering from the programmer manufacturer www.mcumall.com in Canada is too costly because import fees and VAT are added for products from outside Europe.

Likes(1)Dislikes(0)
]]> By: Albert van Bemmelen https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407640 Sat, 02 Sep 2023 15:13:52 +0000 https://jestineyong.com/?p=30923#comment-407640 In reply to Waleed Rishmawi.

Understood. Your EZP2010 is a special fast Bios chip copier that got newer upgrade models like the EZP2023. It also supports SPI programming mode ideal for reading and flashing monitor Bios chips. Which is something also all universal programmers are able to and more! And they also are really fast like the RT809H and the TL866II. Have a good and blessed Weekend too Waleed!

Likes(2)Dislikes(0)
]]> By: Parasuraman S https://jestineyong.com/fixing-brand-new-never-working-nano-3-0-arduino-modules/comment-page-1/#comment-407629 Sat, 02 Sep 2023 13:56:31 +0000 https://jestineyong.com/?p=30923#comment-407629 In reply to Albert van Bemmelen.

Many thanks!

Likes(3)Dislikes(0)
]]>