Don't Miss

How To Fix LED Lantern

By on September 6, 2017
how to repair lantern led

 

 

 

 

 

 

 

 

 

 

LED Lantern repair

The complaint of this LED Lantern light was it can’t be turned on but when the AC power cable was connected the charging light was On as seen from the photo below:

fix led lamp

Th below photo is the specification of the LED lantern and it has a battery capacity of 6000mAh and have 60 pieces of LEDs.

LED Lantern spec

Once the cover was opened, the first thing I do was to check on the battery voltage. It showed 3 volt and seems to be good but why it can’t be turned On?




I had to remove the switch more power supply to check if there is any problem with it.

LED Lantern battery charger problem

The power supply was removed and on visual inspection I found one of the resistor leads was rusted and broken. I further checked on all the corresponding components and did not find any bad components.




I soldered an additional lead between the resistor and the circuit board joint and after that powered it up and to my surprised the LED lantern worked fine-you can see the following photo.

how to repair lantern power supply

how to fix lantern led

how to fix and repair led lantern

Conclusion- Many times electronics  equipment can be easily repaired. The problems such as dry joints, broken circuit track, loosen connectors and bulged electrolytic capacitors can be tackled in the shortest time. This can easily add to the overall earning of this electronics repairing field.

suranga

This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.




Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

P.S-  If you enjoyed reading the above article, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check out his previous post in the below links:

https://jestineyong.com/how-to-repair-display-problem-in-canca-tv/

 

Likes(76)Dislikes(0)

7 Comments

  1. Robert Calk

    September 6, 2017 at 10:06 pm

    Good job, Suranga.

    Likes(1)Dislikes(0)
  2. Parasuraman S

    September 6, 2017 at 11:15 pm

    Well done! You handle things with so much ease that comes out only from prolonged hard work and involvement in servicing!

    Likes(1)Dislikes(0)
  3. Calum

    September 7, 2017 at 10:50 am

    good job

    Likes(1)Dislikes(0)
  4. Albert

    September 7, 2017 at 5:53 pm

    I guess the corroded resistor was a current limiter resistor. It probably was
    used as an overcurrent safety 'fuse' although it now was the broken leg that inhibited the Lantern from working, noticing the low resistor value if I saw it right. I suppose that all 60 led's were switched in parallel to the 3V battery?

    Albert.

    Likes(1)Dislikes(0)
  5. Yogesh Panchal

    September 7, 2017 at 10:37 pm

    well done! Suranga

    Likes(0)Dislikes(0)
  6. Geoffrey Wight

    September 10, 2017 at 7:49 pm

    Nice save! Simple fix and well done work.

    Likes(0)Dislikes(0)
  7. bela kokas

    September 11, 2017 at 5:37 pm

    good job.

    Likes(1)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close