Comments on: IBS Store – Electronics Supplier https://jestineyong.com/ibs-store-electronics-supplier/ Semiconductors, Test Equipments, Circuit Board Troubleshooting, Electronic Repair Courses and Many More! Wed, 28 Nov 2012 21:05:21 +0000 hourly 1 https://wordpress.org/?v=5.4.19 By: aelmomurilo https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-164762 Wed, 28 Nov 2012 21:05:21 +0000 https://www.jestineyong.com/?p=2915#comment-164762 gostei das respostas

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5930 Sat, 26 Jun 2010 19:42:49 +0000 https://www.jestineyong.com/?p=2915#comment-5930 Thanks a lot mr Yong

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5929 Sat, 26 Jun 2010 19:42:25 +0000 https://www.jestineyong.com/?p=2915#comment-5929 hi Yestine,i solved a problem in a monitor too (it works with fet k2645,only vivax tv problem not solved

Likes(0)Dislikes(0)
]]> By: admin https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5926 Sat, 26 Jun 2010 01:04:35 +0000 https://www.jestineyong.com/?p=2915#comment-5926 HI Ben,

If the power fet is located in power section then you can use K2645 as replacement.

Jestine

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5925 Fri, 25 Jun 2010 20:09:44 +0000 https://www.jestineyong.com/?p=2915#comment-5925 is there any way to find what fet is located on samsung monitor,i ask for that information few questons before

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5924 Fri, 25 Jun 2010 20:07:00 +0000 https://www.jestineyong.com/?p=2915#comment-5924 first power board (small board),second Mainboard (big board) with Flyback Transformer

Likes(0)Dislikes(0)
]]> By: admin https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5912 Thu, 24 Jun 2010 22:01:40 +0000 https://www.jestineyong.com/?p=2915#comment-5912 HI Ben,

May i know what two boards you are referring to? I believe one of the board that had cause the fuse to blow and you need to check on the semiconductors

Jestine

Likes(0)Dislikes(0)
]]> By: admin https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5911 Thu, 24 Jun 2010 21:59:52 +0000 https://www.jestineyong.com/?p=2915#comment-5911 HI Ben,

Posistor can't be test and you need to direct replace and retest. For the bridge rectifier you can test the individual diode in the package using meter. All these testing i have compiled it into an ebook at Testing Electronic components dot com.

Jestine

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5905 Thu, 24 Jun 2010 00:59:07 +0000 https://www.jestineyong.com/?p=2915#comment-5905 and sommething more,i know i am borring, after i disconnect cable betwen two board fuse dont blow

Likes(0)Dislikes(0)
]]> By: Big Ben https://jestineyong.com/ibs-store-electronics-supplier/comment-page-1/#comment-5904 Thu, 24 Jun 2010 00:53:45 +0000 https://www.jestineyong.com/?p=2915#comment-5904 but for vivax crt,how can i test posistor and bridge recifier

Likes(0)Dislikes(0)
]]>