Don't Miss

LOGITECH Mouse Repaired

By on March 26, 2016
mouse repair

 

 

 

 

 

 

 

 

 

This Mouse LOGITECH Model Number: M-SBF96 was given to me with two complaints:

  • The cursor was not moving fine in the Display.
  • The right click was not working.

Note: this device was checked on by another tech that was what the owner told to me. As you can see in the photos below it’s an Optical device with PS/2 connector.

LOGITECH Mouse Repaired

First thing done was to open the device, a piece of cake, only one screw.

2

The first complaint previously mentioned could be seen at simple sight and it was fixed immediately by pushing down the plastic cover of the LED till the clips were fixed in the PCB, look at the pictures below:

3

4

To solve the second complain previously mentioned it was necessary to look for spare parts of an unused mouse.

5

One of these micro switches was de-soldered to substitute the bad one in the original PCB of the mouse.

6

Once the micro switch was substituted, and the mouse was completely armed, connected to the PS/2 slot of the motherboard, and the PC switched on, it worked perfectly fine. Look at the photos below as an example.

7

8

humbertophoto5

This article was prepared for you by Humberto Rodriguez, one of our ‘Master Authors’ from Cuba.

Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-  If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check his previous repair article in the below link:

https://www.jestineyong.com/hard-disk-drive-hdd-was-out-of-order/

 

Likes(82)Dislikes(0)

16 Comments

  1. suranga bandara, Suranga Electronics

    March 26, 2016 at 6:00 pm

    hi, Mr- Humberto,

    Successful PS/2 Mouse Repair.

    Likes(2)Dislikes(0)
    • Humberto

      March 29, 2016 at 12:40 am

      Thanks Suranga.

      Likes(0)Dislikes(0)
  2. albert van bemmelen

    March 26, 2016 at 6:21 pm

    Hi Humberto. Nice to see you are back with a new repair.
    Those Microswitches are much better and longlasting compared to
    the mostly hard to replace cheapish Membrane switches. And the
    clicking sound they make is a plus.
    It would be nice if the Electronics industry would manufacture
    easy to replace low hight Membrane switches too.
    Because most remote controls simply can't be fixed with those high
    Microswitches.

    Likes(3)Dislikes(0)
    • Humberto

      March 29, 2016 at 1:02 am

      Yes Albert, remember I was abroad, and then separated from repairs. But I confess I had a good time with my sister, niece and little nephew. I could not repair a Amplifier Audio System there in Ecuador because I had not my tools with me.

      Likes(3)Dislikes(0)
  3. Robert Calk

    March 27, 2016 at 12:07 pm

    Good job, Humberto. I'm glad you got it repaired.

    Likes(0)Dislikes(2)
    • Humberto

      March 29, 2016 at 12:43 am

      Hi Robert, I was lost of this blog because I was abroad. The Cuban people is very happy and hopeful with the visit of President Barack Obama.

      Likes(0)Dislikes(0)
      • albert van bemmelen

        March 29, 2016 at 9:45 pm

        And with the free concert of the Rolling Stones no doubt! (LOL)

        Likes(3)Dislikes(0)
    • Robert Calk

      March 30, 2016 at 6:57 am

      Hi Humberto,
      There are some that are not so happy about his visit. I have not had anything to make an article about in a while also. I had a few that did not pan out. I'm waiting for a new EEPROM programmer to get here right now so I can check out a Samsung LCD TV. According to my books the panel is bad. But I'm going to experiment with it and check into some things. The new programmer, MiniPro TL866A is supposed to work with Win10 and also has ICSP capability. I also have another hobby now, leatherworking. It is a lot of fun making my own leather pieces! My first project was a knife sheath I finished the other day.

      Likes(4)Dislikes(1)
  4. Parasuraman S

    March 27, 2016 at 8:05 pm

    Good job! The work is very minute, and you have manage it with ease, as these are peanuts for you!

    Likes(0)Dislikes(0)
    • Humberto

      March 29, 2016 at 12:45 am

      Thanks Parasuraman.

      Likes(0)Dislikes(0)
  5. Henrique J. G. Ulbrich

    March 27, 2016 at 8:37 pm

    Good job, Humberto. Sad to know that this gadget was "prepared" before by another. As a matter of fact this other "technician" is really very bad...

    Likes(0)Dislikes(0)
    • Humberto

      March 29, 2016 at 12:55 am

      Hi Henrique, I did not publish any photo of the PCB of this mouse, specifically of the bottom with the solder joints and its surround areas of the micro-switch because I felt sorry about the destruction the other tech had done, I suppose he/she used a soldering iron with too much power. But anyway, the mouse was saved.

      Likes(2)Dislikes(0)
  6. Gopal Sharma

    March 28, 2016 at 1:42 pm

    Thanks for sharing. But mouse switch is also repairable. I have opened it and repaired so many switches by cleaning their contacts, then it works as a new switch.

    Likes(4)Dislikes(0)
    • Humberto

      March 29, 2016 at 12:57 am

      Yes Gopal, you are right. But this time I had of spare and and could save some time. Thanks anyway.

      Likes(0)Dislikes(0)
  7. Yogesh Panchal

    March 28, 2016 at 2:48 pm

    Humberto,
    Good job! Thanks for sharing.

    Likes(0)Dislikes(0)
    • Humberto

      March 29, 2016 at 12:58 am

      Thanks Yogesh.

      Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close