Comments on: NCP1203P60 Datasheet https://jestineyong.com/ncp1203p60-datasheet/ Semiconductors, Test Equipments, Circuit Board Troubleshooting, Electronic Repair Courses and Many More! Thu, 03 Sep 2015 13:23:40 +0000 hourly 1 https://wordpress.org/?v=5.4.19 By: Jestine Yong https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-252844 Thu, 03 Sep 2015 13:23:40 +0000 https://www.jestineyong.com/?p=3936#comment-252844 In reply to jayesh.

HI Jayesh,

I do not have this monitor with me thus I would not know what will be the value. I suggest that you look for the schematic from the internet. From ic datasheet it seems that the value is more than 4.7 k Ohm

Jestine

Likes(0)Dislikes(0)
]]> By: jayesh https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-252644 Wed, 02 Sep 2015 02:40:32 +0000 https://www.jestineyong.com/?p=3936#comment-252644 Dear sir,
I got a power supply usig ic 1203p60 in this resistor burned( pin no 8) ie filter to ic pin no 8 pls suggest me the resistor value, what will be the cause
it is a benq lcd monitor model w1508

Likes(0)Dislikes(0)
]]> By: Jestine Yong https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-211445 Tue, 29 Apr 2014 03:44:49 +0000 https://www.jestineyong.com/?p=3936#comment-211445 In reply to marina.

Hi Marina,

Yes you right.

jestine

Likes(1)Dislikes(0)
]]> By: marina https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-211422 Tue, 29 Apr 2014 00:18:23 +0000 https://www.jestineyong.com/?p=3936#comment-211422 In reply to Dimon.

Hi Mr. Yong! I had the same problem like Dimon. It happened when I replaced an 1203P60 for an NCP1203P60. I beging to believe that both IC's are not really similar.
Marina

Likes(0)Dislikes(0)
]]> By: Dimon https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-128009 Tue, 02 Oct 2012 02:33:23 +0000 https://www.jestineyong.com/?p=3936#comment-128009 And the same monitor (benq) and power board. With "new" IC`s R603 was in smoke. I installed 1203P60 in SMD-case, marked as "203D6" and monitor started to work as expected. This new IC`s is defect or relabeled!

Likes(1)Dislikes(0)
]]> By: Jestine Yong https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-125573 Fri, 28 Sep 2012 12:27:38 +0000 https://www.jestineyong.com/?p=3936#comment-125573 In reply to Bradley Brake.

Hi Bradley,

That is why sometime I do check on the new components first before installation.

Jestine

Likes(0)Dislikes(0)
]]> By: Bradley Brake https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-125498 Fri, 28 Sep 2012 08:19:16 +0000 https://www.jestineyong.com/?p=3936#comment-125498 There have been problems with some suppliers here on different components, like capacitors that are leaky, solid state semiconductors defective.
Another supplier woud be a very good idea.

Likes(0)Dislikes(0)
]]> By: Jestine Yong https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-65988 Tue, 10 Apr 2012 13:37:07 +0000 https://www.jestineyong.com/?p=3936#comment-65988 In reply to Alfred Morrison.

HI Alfred,

Yes the only way to find out is to buy from another supplier and retest.

Jestine

Likes(0)Dislikes(0)
]]> By: Alfred Morrison https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-65870 Tue, 10 Apr 2012 05:03:59 +0000 https://www.jestineyong.com/?p=3936#comment-65870 Hi if the datasheet state the same information then it could mean that you bought an immitated part i will sugest you buy from a different shop. have a blessed easter

Likes(0)Dislikes(0)
]]> By: beh https://jestineyong.com/ncp1203p60-datasheet/comment-page-1/#comment-63453 Sat, 31 Mar 2012 18:41:40 +0000 https://www.jestineyong.com/?p=3936#comment-63453 HI MR YONG

ok i will wait here to have the result of this test.
regards
beh

Likes(0)Dislikes(0)
]]>