Comments on: Panasonic (National) Remote Control Fan No Power Symptom

By: Avraham

Avraham — Sun, 03 Oct 2021 05:49:55 +0000

Hi I have a similar model of fan with speed problems, from your post it looks like the board is on the top part of the fan above the blades and the wires are soldered onto the board without release connectors? Can this fix be done without removing the fan from the ceiling?

Likes(0)Dislikes(0)

By: Eric

Eric — Sat, 04 Apr 2020 04:22:18 +0000

hi wong,

this article problem same like we facing recently. press remote control can hear sound tik but motor speed not change and remote must nearest to fan only can function and normally timer light can on when press. now timer light cannot always on when press timer button. what is possible cause this problem. please help. thank you so much.

Likes(0)Dislikes(0)

By: Hariz

Hariz — Tue, 04 Sep 2018 08:08:51 +0000

Good info..Nice joob

Likes(0)Dislikes(0)

By: Syed Asrizal

Syed Asrizal — Thu, 19 Apr 2018 01:07:51 +0000

I have exactly the same model and my problem is the low speed capacitor blown..i cant see the capacitor value..if u not mind can u give me the low speed capacitor value..btw very helpful thread..thanks in advance..

Likes(0)Dislikes(0)

By: maybelchh

maybelchh — Sat, 03 Mar 2018 09:17:07 +0000

I have the exact same ceiling fan model and will check the caps. At speed 1, it is not turning - not at all. other speed works ok

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Mon, 08 May 2017 23:45:58 +0000

In reply to KF Yap.

Hi Kf Ya,
If the resistor is blown then it will have an open circuit and the circuit may not work. Your problem is mainly due to bad capacitor, open component (burnt resistor), bad circuit track or even dry joints. For your information I do not have the diagram of this fan thus I would not know the value of the resistor. Unless if you can compare a working unit then you can find the exact resistor value.

Jestine

Likes(0)Dislikes(0)

By: KF Yap

KF Yap — Sun, 07 May 2017 14:39:35 +0000

I had this National Ceiling Fan MY14S that need a push to start the fan motor rotation. The Polyester Capacitor already changed to new one after finding old one to be less capacitance value.Resistor R31 is blown out with a burn mark (hole in pcb)Will faulty triac (SCR1 or SCR2 or SCR3 cause any of this problem of requiring push start of fan motor ? Once push start the fan motor can rotate by itself. The Remote controller is working for start/stop , Speed 1 or 2 or 3. while fan motor is rotating.
Hope you can help me on this matter.Thank you.

Likes(0)Dislikes(0)

By: Zam

Zam — Sun, 12 Feb 2017 14:15:29 +0000

Hi YH Wong, can you share with me value for diode D101.

Thanks.

Likes(0)Dislikes(0)

By: Humberto

Humberto — Mon, 31 Oct 2016 15:16:20 +0000

Good repair YH Wong. Good explanations.

Likes(1)Dislikes(0)

By: Robert Samuel

Robert Samuel — Wed, 26 Oct 2016 08:42:27 +0000

Good repair job. The 3 large Red capacitors - do these go off value often in this model of fan?
Thanks.

Likes(0)Dislikes(0)