Comments on: Playing with IC’s: Part 2 https://jestineyong.com/playing-with-ics-part-2/ Semiconductors, Test Equipments, Circuit Board Troubleshooting, Electronic Repair Courses and Many More! Fri, 10 Jul 2015 17:56:05 +0000 hourly 1 https://wordpress.org/?v=5.4.19 By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-243345 Fri, 10 Jul 2015 17:56:05 +0000 https://www.jestineyong.com/?p=9613#comment-243345 In reply to jun.

Hi Jun. I am happy that you enjoyed it. Be sure to read the Part 3 article!

Likes(1)Dislikes(0)
]]> By: jun https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-242934 Tue, 07 Jul 2015 02:50:58 +0000 https://www.jestineyong.com/?p=9613#comment-242934 I'm very much happy upon reading this article, Hopefully can get more knowledge about electronics. thanks robert

Likes(0)Dislikes(0)
]]> By: STEVEN NEO https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237713 Mon, 01 Jun 2015 08:49:22 +0000 https://www.jestineyong.com/?p=9613#comment-237713 In reply to Robert Calk.

Hi ... Robert. nice to hear that finally you had succeed.
making mistake is just part of the life but we will learnt a lesson.
cause i always make this type of mistake and kill the components and will careful before change the parts. will check through pin to pin and component to component.
BONUS ... can help other to solve it!
you are welcome .. ROBERT.
Thanks.

Likes(1)Dislikes(0)
]]> By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237654 Sat, 30 May 2015 07:45:29 +0000 https://www.jestineyong.com/?p=9613#comment-237654 In reply to David.

Hi David. As it turns out Steven was right! I'm working on the article now, and I'm getting nearly 3.2V at 320KHz on the first IC that I pulled out of the bag after fixing the breadboard as Steven suggested. I'm surprised that I didn't notice my mistake, but no one is perfect.
I should be sending the article to Mr. Yong in a day or two.
Thanks guys - I appreciate the comments and suggestions.
Oh, also in Playing with IC's Part 3, I will be revealing a secret that few people know about! I don't remember ever reading about it in any electronics books. So don't miss it!

Likes(1)Dislikes(0)
]]> By: STEVEN NEO https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237497 Mon, 25 May 2015 04:03:17 +0000 https://www.jestineyong.com/?p=9613#comment-237497 In reply to David.

Seriously folks ???!!!!!heard about Ice Cube holder ???!!!
just kidding.
don't under tension ..... this is electronic world ,we are just playing with SMD IC.the point is fun, don't miss out this fact,please !!!
we like to make an alien web like wiring/circuit , that's it !
ROBERT is our fun GURU.

Likes(0)Dislikes(0)
]]> By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237493 Mon, 25 May 2015 00:50:37 +0000 https://www.jestineyong.com/?p=9613#comment-237493 In reply to David.

Thanks. I've soldered many IC's without ruining them. My soldering is not the problem.

Likes(0)Dislikes(0)
]]> By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237492 Mon, 25 May 2015 00:48:18 +0000 https://www.jestineyong.com/?p=9613#comment-237492 In reply to STEVEN NEO.

That may be the problem. I only raised the voltage on a couple of the IC's, so I'll change the circuit and check them out. Thanks.

Likes(0)Dislikes(0)
]]> By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237489 Mon, 25 May 2015 00:27:19 +0000 https://www.jestineyong.com/?p=9613#comment-237489 In reply to Humberto.

Thanks Humberto.

Likes(0)Dislikes(0)
]]> By: Robert Calk https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237488 Mon, 25 May 2015 00:20:37 +0000 https://www.jestineyong.com/?p=9613#comment-237488 In reply to Albert van Bemmelen.

Hi Albert. I have the old fashioned ones also but they are no way near as handy as my Hakko 808. The vacuum pump is built into the de-soldering gun. I have no idea what you are talking about it not being included - sounds like a fake 808 to me.

Likes(0)Dislikes(0)
]]> By: David https://jestineyong.com/playing-with-ics-part-2/comment-page-1/#comment-237461 Sun, 24 May 2015 04:45:19 +0000 https://www.jestineyong.com/?p=9613#comment-237461 Seriously folks!?!?...has no one heard of a IC holder. You solder that into the circuit and plug your IC into that...just clean the pins if they don't look new. I'm almost sure you busted your IC soldering them in. I have ordered and replaced many ICs without static gear and they still are working.

Likes(0)Dislikes(0)
]]>