Comments on: Repairing LED FloodLight

By: Jestine Yong

Jestine Yong — Mon, 08 Apr 2019 13:17:08 +0000

In reply to Kim.

Hi Kim,

Sorry we no longer repair floodlight.

Jestine

Likes(0)Dislikes(0)

By: Kim

Kim — Mon, 08 Apr 2019 10:24:11 +0000

Good Day , Just a request , do you guys repair 200W Eurolux LED Floodlights ?

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Wed, 27 Dec 2017 13:58:16 +0000

In reply to Mash.

Hi Mash,
You need to replace the burnt LEDs because shorting it will put pressure on the other LEDs. Most smps nowadays does not have preset to tune lower down the output voltage thus it would be hard to do the modification. Try search from aliexpress to see if you can find the type of LEDs for your flood light.

Jestine

Likes(0)Dislikes(0)

By: Mash

Mash — Tue, 26 Dec 2017 21:22:37 +0000

hi, i have 50 Watt LED Flood Light IP66 and some leds are burnt, how should i reduce the voltage reaching the good leds (if i by-pass the burnt leds using a wire)?

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Sat, 12 Jul 2014 13:49:52 +0000

In reply to Amagunba Stephen.

HI Amagunba,

You are welcome!

Jestine

Likes(0)Dislikes(0)

By: Amagunba Stephen

Amagunba Stephen — Sat, 12 Jul 2014 11:51:52 +0000

Hi Jestine. Am much grateful with this news letter of yours, keep on doing the good works. Truely i was even thingking of quiting. But you have really really giving me hope. Thanks a trillion.

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Sat, 10 May 2014 00:17:56 +0000

In reply to Sherwin Baptista.

Hi Sherwin,

Glad that you liked the article-thanks.

Jestine

Likes(0)Dislikes(0)

By: Sherwin Baptista

Sherwin Baptista — Fri, 09 May 2014 14:50:51 +0000

Hello sir Jestine,
This seems to be an interesting article.
I am in this electronics line since long. I have opened different power supplies just to get their components especially the inductors and other components. I believe that the inductors (ferrite based) are not so eaisly available in the market,i searched damn hard,wasn't lucky enough. i haven't shopped online as yet. Just broke open power supplies and get those rare components that suite my project well.
I've bought myself an old power supply from one of the paper recycling stores they said it was a bad one. Actually i wanted to repair it but i found it too tough since they were high wattage ones.
Previously, i'd purchase old power supplies the PC ones for sure just to get those rare components, but i will not let go off with the repairing idea. I would rather try hard and work at my best, for there could be a great saying ''success is at your hands until you work hard''.

To conclude with, i would say yours was a really interesting article
All round the world DIYs would really benefit from your article.

Keep up with the good work and may god bless.

Regards,
Sherwin from Mumbai.

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Thu, 06 Feb 2014 12:11:40 +0000

In reply to Keith Ford.

HI Keith,

Just scrap it off and clean with thinner.

Jestine

Likes(0)Dislikes(0)

By: Keith Ford

Keith Ford — Wed, 05 Feb 2014 17:18:06 +0000

What is you farvorite method to remove the carbon from the circuit board?

Likes(0)Dislikes(0)