Comments on: Review Of Jingyan M6013 AutoRanging Capacitor Tester

By: Jestine Yong

Jestine Yong — Sun, 30 Jan 2022 06:40:38 +0000

In reply to Parasuraman S.

Hi Parasuraman,

You are welcome.

Jestine

Likes(0)Dislikes(0)

By: Parasuraman S

Parasuraman S — Sun, 30 Jan 2022 03:49:28 +0000

Happened to see it only now! Very useful review! Many thanks!

Likes(0)Dislikes(0)

By: Anwar Y Shiekh

Anwar Y Shiekh — Tue, 16 Mar 2021 17:40:01 +0000

Pity it does no also measure the ESR as some failing capacitors can still have a capacitance in range.

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Mon, 26 Jun 2017 14:43:38 +0000

In reply to Abdur-Rab.

Hi Abdur,
You are welcome.

Jestine

Likes(0)Dislikes(0)

By: Abdur-Rab

Abdur-Rab — Tue, 20 Jun 2017 06:48:07 +0000

Very Good Day Dear Jestine Yong!!

Many thanks for all your mails which reach me regularly.

I was hampered due to my office job / hours to go through all your mails. But occasionally I used to enjoy your mails.

All stuff is extremely helpful for me and for the beginners these articles / e.books / comments etc. are off-course like a Wealthy Site.

Anyway, I will keep in touch with you.

Thanks again for being so nice in all respects.

Best Regards

Abdur Rab

Likes(0)Dislikes(0)

By: Anwar Shiekh

Anwar Shiekh — Sat, 27 Jun 2015 13:32:46 +0000

I very much like the Peak atlas ESD+, which also gives the ESR measurement.

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Thu, 29 May 2014 23:18:34 +0000

In reply to Julio Mamani.

Hi Julio,

Congratulation.

Jestine

Likes(1)Dislikes(0)

By: Julio Mamani

Julio Mamani — Wed, 28 May 2014 15:46:12 +0000

In reply to Jestine Yong.

Dear Jestine good morning, and told him that we solve the problem of light the display (backlit) so I stand before turning down the button on range (zero) and I turn there you hold the range button (Zero ) I get a message on screen (CAL MODE) button lost range (zero) button once preciono range (zero) and light or backlight is on or Off.
regards

Likes(0)Dislikes(0)

By: Jestine Yong

Jestine Yong — Wed, 28 May 2014 10:24:36 +0000

In reply to Julio Mamani.

Hi Julio,

Since I have not repair a broken Jingyan m6013 meter before thus I can't give you a direct answer.I suggest that you trace from the red probe connector to see if there is any bad components. By the way how does this meter have problem? The meter itself have problem or went through a high voltage discharge from a big cap?

Jestine

Likes(0)Dislikes(0)

By: Julio Mamani

Julio Mamani — Tue, 27 May 2014 14:35:05 +0000

In reply to Jestine Yong.

Estimated jestine what happens is that the tester performs well measurements, for example when we put a 16 volt capacitor 4700uf x and gives me the measurement capacitor, but it happens that the LED or display light does not light, and U1 revice and U2, Q1, Q2, Q3 and resistors are in good condition. but I have no Voltage at resistor R11 which powers the LED lighting of the screen, I wondered what might be wrong or am I missing something? regards
Excuse my bad translations writes a person peru (Latino)

Likes(0)Dislikes(0)