Don't Miss

Olik Active Speaker Repair

By on July 11, 2017
usb active speaker repair

 

 

 

 

 

 

 

 

olik speaker repair

The complaint with this Olik active speaker was the USB port and the display were not functioning. See the photo below of the no display symptom.




To me the problem more like a no power symptom in the USB circuit board.

olik speaker fix

The first thing I did was to remove the cover and access to the USB card and check for the dc supply. Most USB card uses 5 volt DC to operate and my voltmeter registered 5 volt when measuring on the DC supply. This means the power supply was good and the problem is in the USB card itself.

fix olik activespeaker

I did another careful looked at the USB card and found that those ICs used were not common (hardly can be found in the market). It could be the program had corrupted but because I do not have access to the parts and the program, I told myself that this problem was not worth to repair.

how to repair olik active speaker

So I bought the whole new USB card from the market and replace it and soldered the Antenna wire too at the back of the card.

Repairing olik active speaker

fixing olik speaker

Once done fixing the USB card and powered On, the display lighted up as seen from the photo below:

usb active speaker fix

In certain cases only, it is not really worth the time to repair the circuit board due to the unavailability of the parts. Besides the customer can get his device back sooner as possible if I directly replaced the card.  Ok, hope to see you again in the next article.

suranga

This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.




Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

P.S-  If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check out his previous post in the below link:

https://jestineyong.com/pincushion-problem-in-crt-tv-repaired/

 

Likes(98)Dislikes(0)

13 Comments

  1. Albert van Bemmelen

    July 11, 2017 at 4:10 pm

    Repairing a defect old board indeed is not worth the time searching for replacement parts or waiting on them to arrive especially if the board can be bought completely new. And this new board even looks almost identical to the old defect one anyhow! Which fits in place without any problem too! Seeing the name Olik on the quite heavy device, it must have been a funny manufacturer who turned its weight around from Kilo to Olik? Thank you for sharing your successful repair Suranga.

    Likes(4)Dislikes(0)
    • Suranga Electronics

      July 12, 2017 at 1:26 am

      Thank you Mr,Albert.

      Likes(3)Dislikes(0)
  2. Mark

    July 11, 2017 at 4:47 pm

    So true Suranga, the price of complete circuit boards in comparison to the availability of some components make it hard to repair at a component level. Well done on the diagnosis.

    Likes(2)Dislikes(0)
    • Suranga Electronics

      July 12, 2017 at 1:28 am

      Thanks
      Mr,Mark !

      Likes(1)Dislikes(0)
  3. Joop

    July 11, 2017 at 5:44 pm

    Hello Suranga, Thanks for sharing your repairs. I wonder how to find these parts.

    Likes(3)Dislikes(1)
  4. Anthony

    July 11, 2017 at 6:20 pm

    Good repair Suranga and of course time is money !

    Likes(2)Dislikes(0)
  5. Yogesh Panchal

    July 11, 2017 at 9:53 pm

    Good job! Suranga.

    Likes(2)Dislikes(0)
  6. Michael

    July 12, 2017 at 7:02 am

    Thanks Suranga for this wonderful article.it seems SMT technology is all about replacing boards which makes servicing electronic less interesting.

    Likes(2)Dislikes(0)
  7. Alphonsus Lim

    July 12, 2017 at 1:40 pm

    Thanks Suranga for all the wonderful articles you have written and posted. Your articles always interest me.

    My sentiments exactly, is not really worth the time to repair the circuit board due to the unavailability of the parts. More over these cards are now available at a very low and reasonable price. I beleive that is the route technology is advancing today, pluck and play. Hence everything will be made to modules and reduce to cards and components.

    Likes(4)Dislikes(0)
  8. Robert Calk

    July 13, 2017 at 2:45 pm

    Good job, Suranga. Sometimes we can't even get new boards. But it's nice when we can get the parts to fix devices and save them from the trash.

    Likes(3)Dislikes(0)
  9. charles

    July 19, 2017 at 2:49 am

    Well done thank you for sharing

    Likes(1)Dislikes(0)
  10. charles

    July 19, 2017 at 2:50 am

    helpful article thank you for sharing

    Likes(1)Dislikes(0)
  11. Humberto

    July 19, 2017 at 12:08 pm

    Good for you Suranga, congrats.

    Likes(1)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close