Don't Miss

A Shorted/Dead Welding Machine Repaired. Model: Apex ACR-180

By on March 18, 2023
welding machine repair

A welding technician brought many welding machines for repair. This one was urgently needed so I started right away finding the fault in this machine. The technician explained that the machine comes on but does not weld because when I powered it on though a current limiter, the fan came on but the fins on the fan were all broken and based on that I figured right away, we are going to have blown parts inside.

welding machine repair

I checked for voltages while the machine was on and as expected, it was dead, no reading whatsoever.

The technician explained that when he was welding, he heard the fan running he did know that the fins are broken therefore no cooling was being done inside.

how to fix a welding machine

Obviously, this machine was seen by another technician and he did not do a good job because of the mess that was done here. There are SMD diodes and resistors in this area but they were replaced with normal resistors and not with the same value.

burnt smd value

ss12 datasheet

Click here to access SS12 Datasheet

I started the repair here first before heading to replace the blown IGBT on the other side of the machine. I replaced the two resistors on both side and a diode.

The parts replaced here are SS14 diode, 220 and 5.1 ohm SMD resistors. The diode on the other side was ok so no replacement there.

burnt igbt

Other the other side of the welding machine is a completely different story, the IGBT 60N60FDI was blown to pieces, the other IGBT with the same part number was no burnt like these but still shorted and needed replacement.

IGBT 60N60FDI

That is one of the replacements for the blown IGBT and of course adding a thermal paste is a must in this situation.

blown igbt

This is the other IGBT which is found on this heat sink; the bridge rectifier was tested and found ok so I did not replace that.

I cleaned the area, added a new IGBT on this side as well and I was about to test when the customer called me to ask if the machine is ready. I told him almost ready because I am about to install a new fan and then will test it out. He told me not to install the fan because he wants to do it himself. I explained that I will not take any responsibility if the parts are blown again and the customer agreed (thinking that he is saving money this way).

how to test welding machine dc output voltage

In order for me to test the machine, I installed a fan and powered it on using a current limiter device; this time I was able to read some voltage readings here and that is a very good sign.



My brother tested the machine out and it was up and running according to specs. I took the fan out, called the customer for pick up and when he came I made him sign a document that it is his responsibility not mine if the welding machine goes dead due to lack of cooling inside it.

Mission Accomplished.

waleed Rishmawi

This article was prepared for you by Waleed Rishmawi, one of our ‘Master Authors’ and currently working in the Bethlehem area of Palestine repairing electrical and electronic equipment.

P.S- Do you know of any your friends who would benefit from this content that you are reading now? If so, forward this website to your friends or you can invite your friends to subscribe to my newsletter for free in this Link.

Note: You can check his previous article on Successfully Repaired A Dead Hover Board Charger 

Likes(59)Dislikes(0)

15 Comments

  1. Parasuraman S

    March 18, 2023 at 7:56 am

    Stubborn customers are a part of our deals! An excellent work and you have resolved all issues to your best!

    Likes(4)Dislikes(2)
    • Waleed Rishmawi

      March 18, 2023 at 1:39 pm

      Parasuraman: unfortunately there are a lot of them out there and somehow I have to protect myself. Some customers when I show them this document they change their mind about it and ask me to install a new fan others they do not care. have a blessed day and thanks for your comments.

      Likes(2)Dislikes(1)
  2. Andrew F. Ali

    March 18, 2023 at 10:11 am

    Customers like these sometimes are very difficult to deal with but you did the right thing. Great work too!!!

    Likes(1)Dislikes(0)
    • Waleed Rishmawi

      March 18, 2023 at 1:39 pm

      Andrew: thanks man. have a blessed day

      Likes(2)Dislikes(0)
  3. Albert van Bemmelen

    March 18, 2023 at 6:15 pm

    Why this customer wanted you to fix and replace only the defect components in his machine but not the fan beats me? But it probably was because he already brought in so many dead machines that he wanted to save some money on all his repairs.

    Likes(2)Dislikes(0)
    • Waleed Rishmawi

      March 20, 2023 at 5:11 pm

      Albert: the customer thinks that he was saving money by installing his own fan. the customer does not know the specs for such fan therefore the installation is going to be faulty resulting more damage to the machine. have a blessed day

      Likes(0)Dislikes(0)
  4. Jim Whalen

    March 18, 2023 at 10:18 pm

    The customer probably had 2 or 3 dead machines with spare fans already sitting under his table lol.

    Likes(0)Dislikes(0)
    • Waleed Rishmawi

      March 20, 2023 at 5:14 pm

      Jim: even if he has spare parts, every machine has different voltages, amp rating and rotations so it is not going to work up but ending up bring it back to me that is why I made him sign a paper for future protections. have a blessed day.

      Likes(0)Dislikes(0)
  5. Lynn Blakely

    March 21, 2023 at 5:28 am

    Waleed: You did the right thing in documenting the fact that there is no warranty.
    As you said there are different fans with different, specs.There's no lack of ignorance anywhere in the world. If ignorance is bliss then why aren't there more happy people in the world? LOL

    Likes(1)Dislikes(0)
    • Waleed Rishmawi

      March 21, 2023 at 3:07 pm

      Lynn: thanks man for your comments. totally agree. have a blessed day

      Likes(0)Dislikes(0)
    • Eric

      March 22, 2023 at 11:16 am

      Re "There's no lack of ignorance anywhere in the world. If ignorance is bliss then why aren't there more happy people in the world? LOL"

      Ignorance of lies and deceptions (=most mainstream news and establishment decrees) is bliss because exposing yourself to that is self-propagandization.

      Ignorance of truths is not, or only temporarily or rarely, bliss because it is ultimately self-defeating.

      The FALSE mantra of “ignorance is bliss”, promoted in the latter sense, is a product of a fake sick culture that has indoctrinated its “dumbed down” (therefore TRULY ignorant, therefore easy to control) people with many such manipulative slogans.

      You can find the proof that ignorance is hardly ever bliss (and if so only superficial temporary fake bliss), and how you get to buy into this lie (and other self-defeating lies), in the article “The 2 Married Pink Elephants In The Historical Room –The Holocaustal Covid-19 Coronavirus Madness: A Sociological Perspective & Historical Assessment Of The Covid “Phenomenon”” .... https://www.rolf-hefti.com/covid-19-coronavirus.html

      ““We’re all in this together” is a tribal maxim. Even there, it’s a con, because the tribal leaders use it to enforce loyalty and submission. ... The unity of compliance.” --- Jon Rappoport, Investigative Journalist

      "Separate what you know from what you THINK you know." --- Unknown

      Likes(0)Dislikes(0)
  6. Joven

    March 22, 2023 at 6:49 pm

    How clever of you to have him sign that waiver! Otherwise, he will bring it back to you and accuse you of not doing the job well.

    Likes(0)Dislikes(0)
    • Waleed Rishmawi

      March 23, 2023 at 4:02 pm

      Joven: you are right and that is such a waiver is needed in our field of repair. I have encountered many issues that like before and I am not taking it any longer;it has to stop and that is the way to do it. have a blessed day

      Likes(0)Dislikes(0)
  7. Yogesh Panchal

    March 24, 2023 at 12:11 am

    Good Job! Waleed,
    I never give any option to the customers about quality. i just make the thing right by using good quality of parts which is needed for better performance of the equipment.

    Likes(0)Dislikes(0)
  8. Mahmoud Al-Shaikh

    March 31, 2023 at 11:34 pm

    good job .

    Likes(0)Dislikes(0)

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close