Don't Miss

Could Top247Y IC Substitute For Top246Y?

By on May 15, 2008

713n 

Came in a Samsung 713n 17″ LCD Monitor for repair and the complain was no power. After checking the power primary side found three components that was faulty the power IC top246y, a 15 volt zener diode and a signal diode 1N4148.  Secondary components found to be okay. A search at my spare parts compartment could not locate the TOP246Y power IC thus i just gave it a try on the Top247Y power IC. Guess what? It worked perfectly good and now is under burning in test.

If you are repairing LCD Monitors, please take down this substitution part number, who knows one day you might have need it. Have a good and a happy troubleshooting day!

Likes(3)Dislikes(1)

14 Comments

  1. maiyeuemyphd

    May 16, 2008 at 1:28 am

    Because TOP242-249 same one
    http://www.datasheetcatalog.org/datasheet/powerint/TOP242-249.pdf

    Likes(0)Dislikes(0)
  2. admin

    May 16, 2008 at 8:59 am

    Thanks and this is what we call as power of sharing. In fact i wish that more readers participate in sharing out tips and whatsoever that is related to electronic repair. With this sharing, everyone will learn even with just a simple comment! If you have read from the spec it seems like the higher number can be use to substitute for the lower number.

    You see, not everyone is good in locating schematic diagrams, spare parts, datasheet as some of the websites was buried far below the search ranking. If you have bookmarked any and wish to let us know about the websites, i strongly suggest you post a comment in my blog. I'm really happy about it. Thanks again my friend!

    Likes(1)Dislikes(0)
  3. sunil yadav

    April 28, 2009 at 9:14 pm

    IC hcf 4082

    Likes(0)Dislikes(0)
  4. admin

    April 28, 2009 at 9:17 pm

    Hi Sunil,
    May i know what is your question?

    jestine

    Likes(1)Dislikes(0)
  5. swapnil

    August 10, 2009 at 5:08 pm

    Can you help me in troubleshooting of SMPS which uses TOP247 IC

    Likes(0)Dislikes(0)
  6. admin

    August 10, 2009 at 7:44 pm

    Hi Swapnil,

    What is the problem with the SMPS?

    Jestine

    Likes(0)Dislikes(0)
  7. swapnil

    September 7, 2009 at 11:11 am

    i am getting 3V output instead of 24V.

    Likes(0)Dislikes(0)
  8. admin

    September 7, 2009 at 11:26 pm

    HI Swapnil,

    Try check all components in the primary side and if all tested okay then direct replace the power IC and retest it again.

    Jestine

    Likes(0)Dislikes(0)
  9. Aliyu

    June 24, 2016 at 11:44 pm

    Hello all. I have a problem with my washingachine top246yn ic.how do i get the eqivalent because i could not fine it in my component carbinet. Thanks in anticipation

    Likes(0)Dislikes(0)
    • Jestine Yong

      June 25, 2016 at 8:28 pm

      Hi Aliyu,

      I have not tried other part number because I can get the original part number. Go to aliexpress dot com and key in your part number and you can find lots of seller there.

      Jestine

      Likes(0)Dislikes(0)
  10. Aliyu

    June 26, 2016 at 8:04 pm

    Thank you Jestine i most appreciate.

    Likes(0)Dislikes(0)
    • Jestine Yong

      June 27, 2016 at 11:11 am

      Hi Aliyu,

      You are welcome.

      Jestine

      Likes(1)Dislikes(0)
  11. Elmer vargas

    April 26, 2018 at 11:20 pm

    Hai whats the alternative ic can replace the top 246yn?

    Likes(0)Dislikes(0)
  12. Anas

    August 6, 2021 at 1:08 pm

    I want to check top247y with multimeter. Can any body help me.

    Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close