Don't Miss

No Picture With Violet Raster And No Response To Controls Solved In BPL CRT TV

By on December 26, 2019
crt tv microprocessor ic

 

 

 

 

 

 

 

 

 

 

violet color in crt tv

Model and Make of the TV: BPL LFR20FA1

Complaint reported: Only violet raster, no OSD and not responding to controls or remote.

History: The TV was not switched on for many months, and was kept covered very well.

Action taken: Opened and cleaned the TV gently as the board looked fresh and clean with not much dust and dirt inside. Looked for any bulgy capacitors or strained components on the TV. Could not find any.




Trouble Shooting done: Downloaded the datasheet of uController IC, Toshiba TMP87CM38N, and studied the voltages present. Noticed that the Reset voltage to the IC pin No.33 was Zero. Tracked the standby and found that one transistor which controls the standby command was defective. It was not switching on to let the voltage pass through to the reset pin. Replaced it with A1015 (PNP) transistor. Switched on the TV with the same Violet raster, though this time the TV was responding to commands.
Checked the voltages to Chroma IC No.TB1238AN. Voltages were present. But the Vertical feedback signals were not alright, when checked in Oscilloscope. Suspected a problem in Vertical IC No.TA8403K. After checking all the components around, replaced it. But problem continued. In order to ensure that the RGB is ok on the Tube, I checked the voltages. It was ok. Then replaced the CRT Socket as it could develop fungi inside the pins because of lack of use. No change. Then removed the RGB connection from CRT Board, after switching off the TV, then used bypass pins to supply the + voltage and ground to the CRT Board from the PCB.




First inserted R in and got Red on the screen, then removed it and inserted the Blue and got Blue on the screen. Did the same for Green and got Green on the screen. This indicated that the CRT was ok and RGB was functioning well. Then the suspicion was the Chroma IC. After checking for any defective components around, I replaced the IC. Then the TV got on with the BPL logo and normal raster. Fed a video signal and ran the TV for hours before closing the back cover, as it passed the ageing test.
(I did not replace all the electrolytic capacitors on the board as the customer said that it was a borrowed TV and they did not want to spend too much on it. There was absolutely no dry solder on the Board! The board had a just finished factory look, which was pleasant to see!)

Conclusion: Thus the result was accomplished giving a different experience, result of which was satisfaction jumping to its collection bag!

Datasheet of uController

tv microcontroller ic

Vertical Feedback Signals found on the Chroma IC

bpl tv repair

The uController, Chroma IC Vertical IC

micro controller tv bpl ic

 

bpl color problem in tv repair

scope to check tv signal

Very clean inside and fresh look of PCB

crt tv fix and repair

Proof for perfect working (Picture quality is not good enough due to not changing the electrolytic capacitors)

crt tv bpl color problem fixed

 

This article was prepared for you by Parasuraman Subramanian from India. He is 69 years old and has more than 30 years’ experience in handling antique equipment like Valve Radio, Amps, Reel Tape Recorders and currently studying latest tech-classes conducted by Kerala State Electronics Technicians’ Association. He has done graduation in BBA degree, private diploma in Radio Engineering and retired as MD of a USA company. Presently working as Consultant to Hospital and other institutions.




Please give a support by clicking  on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments.

P.S-If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

You may check on his previous repair article below:

https://jestineyong.com/lightning-struck-bpl-two-in-one-model-cwx-69-restored/

 

Likes(48)Dislikes(0)

13 Comments

  1. Tayo

    December 26, 2019 at 9:27 pm

    Dear Sir...is there anything you cant fix? Well done!

    Likes(2)Dislikes(0)
    • Parasuraman S

      December 27, 2019 at 3:22 pm

      Many thanks! I assume you meant 'is there anything you cannot fix!'

      Likes(0)Dislikes(0)
  2. Albert van Bemmelen

    December 26, 2019 at 10:11 pm

    I guess that there were simply too many capacitors that still needed a replacement. Else I am sure you would have fixed those too after the most difficult part already was done! And your detective tv 'friend' Sherlock couldn't have done it any better.

    Likes(3)Dislikes(0)
    • Parasuraman S

      December 27, 2019 at 3:25 pm

      Ha! Ha! Yes I always like to replace old capacitors! Your tummy shaking humour was enjoyed well!

      Likes(0)Dislikes(0)
  3. Steve

    December 26, 2019 at 10:46 pm

    Great job I miss working on the old crt tv’s those to me are the good old days.

    Likes(1)Dislikes(0)
    • Parasuraman S

      December 27, 2019 at 3:28 pm

      Yes! Working on CRT TVs is a thrilling experience. Mainly because, we have visual symptoms!

      Likes(0)Dislikes(0)
  4. Robert Calk Jr.

    December 27, 2019 at 6:23 am

    Good job, Parasuraman!

    Likes(1)Dislikes(0)
    • Parasuraman S

      December 27, 2019 at 3:29 pm

      Many thanks!

      Likes(0)Dislikes(0)
  5. Waleed Rishmawi

    December 27, 2019 at 5:34 pm

    good job on the repair. I love the shared photos of you repair process. keep up the good works. you just saved a CRT from the trash pin. have a blessed day

    Likes(1)Dislikes(0)
    • Parasuraman S

      December 27, 2019 at 9:56 pm

      Very nice to read your response. Professional Experts like you are the fuel for our continued progress and success! Many thanks!

      Likes(1)Dislikes(0)
  6. Yogesh Panchal

    December 27, 2019 at 6:04 pm

    Good repair! Sir

    Likes(1)Dislikes(0)
  7. Parasuraman S

    December 27, 2019 at 9:56 pm

    Thanks Yogesh!

    Likes(0)Dislikes(0)
  8. KIM

    July 15, 2024 at 12:28 pm

    Dear,Sir Parasuraman
    Thank very much for writting invaluable article.

    By the way, Would you mind to let me know How to remove the RGB connection from CRT Board,and How to use bypass pins to supply the + voltage and ground to the CRT Board from the PCB in detail?

    Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close