Don't Miss

7N65C Power FET Shorted In Singer Hi-Fi DVD

By on July 28, 2017
slow blow fuse black

 

 

 

 

 

 

 

 

 

 

singer dvd no power

The complaint of this Singer HiFi DVD was no power. Once the cover was removed I managed to see three circuit boards in it.




 

It was the power supply board, Main board and DVD card-see the photos below:

fix singer dvd player

Since the complaint was no power so I had to check on the power supply board first. The first thing to check is the main fuse and I found that the main fuse was dark in color indicated there was a serious short circuit in the circuit board.

how to fix no power problem in dvd player

main fuse blow

I checked on the bridge rectifier and components corresponding to the EMI filter and found no shorted component.  Next test was the main power fet. I checked it with my multimeter set to Ohm and found that the three pins power FET was shorted. It showed very low ohm-see the photo below:

 

main fet shorted

The shorted power Fet part number was 7N65C. I continued to check for bad components and did not find any. My conclusion was only two bad components- bad fuse and power fet.

7n65c fet

fet shorted

I did not straight away put the components and power it On, in fact I connect the series light bulb method to make sure there is no longer short circuit. The bulb was bright in the beginning due to capacitor charge and after that it went off. This is a good sign that there was no short circuit and I can put the main fuse and power it up.

series light bulb test

Once the powered was on the Hi Fi came back to life and I was very happy because I can make some profit from this repair work.

how to repair no power in singer Hifi DVD

suranga

This article was prepared for you by Suranga Bandara who owns an Electronics repair shop in Anuradapura, Sri Lanka.




Please give a support by clicking on the social buttons below. Your feedback on the post is welcome. Please leave it in the comments. If you have electronic repair articles to share with us, please contact us HERE.

P.S-  If you enjoyed reading this, click here to subscribe to my blog (free subscription). That way, you’ll never miss a post. You can also forward this website link to your friends and colleagues-thanks!

Note: You may check out his previous post in the below link:

https://jestineyong.com/no-power-in-telesonic-dvd-player-solved/

 

Likes(112)Dislikes(1)

13 Comments

  1. Angelo

    July 28, 2017 at 8:45 am

    Sir Suranga
    i love reading ya article
    u always save time by directly coming to the main point..
    Love ya
    keep blessing us this way by ya experiences...
    Thank ya

    Likes(6)Dislikes(0)
  2. Parasuraman

    July 28, 2017 at 8:59 am

    Excellent expert approach straight to the problem!

    Likes(2)Dislikes(0)
  3. Kushan

    July 28, 2017 at 9:28 am

    Thanks for sharing this Suranga, you have done it clearly with few steps..please share many with us

    Likes(3)Dislikes(0)
    • Suranga Electronics

      July 30, 2017 at 11:02 am

      Thanks Mr,kushan.

      Likes(2)Dislikes(0)
  4. Yogesh Panchal

    July 28, 2017 at 3:32 pm

    Good job! Suranga,

    which legs are shorted of FET let me assume Drain to source?

    Likes(2)Dislikes(0)
  5. Albert

    July 28, 2017 at 9:24 pm

    Good repair Suranga! Any idea what caused it?
    Thanks.

    Likes(1)Dislikes(0)
  6. Robert Calk

    July 28, 2017 at 11:12 pm

    Good job, Suranga. It looks like you soldered the test light wires to the fuse holder. I put insulated alligator clips on my test light wires to make using it much quicker and easier.

    Likes(4)Dislikes(0)
  7. George Persico

    July 29, 2017 at 1:43 am

    Suranga, nice clear troubleshooting steps. We should also note the reason the fuse turns black for those learning. When an overload is just slightly above the rating of the fuse the fuse goes open WITHOUT the black color. However when the overload is severe MANY amperes are drawn through the fuse which vaporizes the fuse wire, causing the black deposit inside the glass.

    Again, nice job

    Likes(3)Dislikes(0)
  8. Mahmoud

    August 1, 2017 at 6:49 pm

    well done

    Likes(0)Dislikes(0)
  9. Humberto

    August 6, 2017 at 12:59 pm

    Good job Suranga, as usual

    Likes(0)Dislikes(0)
  10. Ulises Aguilar Pazzani

    August 21, 2017 at 12:55 pm

    great Job Mr Suranga

    Likes(0)Dislikes(0)
  11. Ulises Aguilar Pazzani

    August 26, 2017 at 12:09 pm

    Mr Bandara good job Sir

    Likes(0)Dislikes(0)
  12. Steve Griffin

    January 16, 2018 at 6:30 pm

    Nice fix. I am looking forward to a proper explanation of How the "light-bulb" is connected to show working status. I have heard this test before and like how this method is so full of information if something further is wrong. Very clever! I am liking these Audio/Hi-Fi repairs. ThankYou! Suranga.

    Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close