Don't Miss

Heating Up and Shutting Down Problem In Massage Device Repaired

By on August 16, 2021
Heating Up and Shutting Down Problem In Massage Device Repaired

 

 

 

 

 

 

A massage therapist brought his device for repair and explained that it keeps shutting down and he cannot hear the fan spinning.

massager repair

I have worked on this device before and now it has a different issue.

Once I opened the top cover and took the fan off for inspection, I noticed that the fan was not spinning.

how to fix a massager

The fan gets its power from the socket marked with the arrow and once I checked that with a multimeter, there was no voltage reading there.

how to fix a massager

I traced the fan socket lines all the way to an IC that was suppose to supply this fan with 24 volts but the IC was not doing its job even when the device is on for a long time. That is why the device was shutting down due to overheating and the fan was not running to keep the device cool enough for operation.

Sorry I did not take a photo of the IC but when checked it online I could not find it anywhere so my other option is to modify the device.

how to fix a broken massager

The power supply was supply the 24 DC output to run the device so I soldered the fan directly to these lines (forgot to take a photo of it, sorry). That means when the power button is pressed on, the fan will be on the whole time. If I found the IC replacement I would have fixed the issue the way it should be but a modification was required at this time.

fixing a massager device

Once the connections were made and the power button was pressed, the fan was running fine and smoothly.



The technician came and gave it a test and he was pleased with the outcome and to that I can say a job well done.

Mission Accomplished.

This article was prepared for you by Waleed Rishmawi, one of our ‘Master Authors’ and currently working in the Bethlehem area of Palestine repairing electrical and electronic equipment.

P.S- Do you know of any your friends who would benefit from this content that you are reading now? If so, forward this website to your friends or you can invite your friends to subscribe to my newsletter for free in this Link.

Note: You can check his previous article on Blu-Tooth Speaker Charging Port Replaced

 

Likes(55)Dislikes(1)

7 Comments

  1. Albert van Bemmelen

    August 16, 2021 at 7:07 pm

    A shame you didn't take a photo of that IC and neither shared the markings on it. It could have helped in finding a replacement for that chip.

    Likes(2)Dislikes(0)
    • Waleed Rishmawi

      August 16, 2021 at 8:45 pm

      next time I will take a photo of parts and send them to you. I doubt the customer will pay more money to replace these parts so the modification his and my first choice.

      Likes(2)Dislikes(0)
      • Ogwang Oscar

        August 20, 2021 at 12:02 pm

        But am happy that the modification works well though you never took the photo of the chip thanks

        Likes(0)Dislikes(0)
  2. Parasuraman S

    August 16, 2021 at 9:01 pm

    Good job there dear friend! Unfortunate that you could not provide important snap of IC! All the best!

    Likes(2)Dislikes(0)
    • Waleed Rishmawi

      August 17, 2021 at 6:19 pm

      Parasuraman: thanks man. I totally forgot about it and I promise next time the device in my shop I will take a photo of it. have a blessed day

      Likes(0)Dislikes(0)
  3. Yogesh Panchal

    August 16, 2021 at 11:58 pm

    Waleed, May be that IC control the working of this FAN when IC receive / sense any temperature feedback.may this blower also get hot on continuous use.

    Likes(0)Dislikes(0)
    • Waleed Rishmawi

      August 17, 2021 at 6:23 pm

      Yogesh: I thought of that actually but so far no complain from the customer and it has been over a month now. have a blessed day

      Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close