Don't Miss

No Power In Chair Massager Repaired

By on July 30, 2021
No Power In Chair Massager Repaired

A lady brought me lots of stuff to repair and one of these was a chair massager that does not power up. She explained that smoke was coming out of the controller and then the massager went dead.

massage chair repair

It is a leather seat massager and the quality of the leather and the making is just amazing.

no power in massager chair fix

Since the customer informed me of smoke coming out of the controller,

I headed directly there and opened up the device.

how to fix massager chair

My new helper (my son) took the screws and the cover off; right away I could smell a bad burn (also confirmed by my helper, LOL). If you look to the left side of the photo you will be able to see the cause of the smell.

There is a bulging part on the top of that IC and it has to be replaced; Part number: ULN2003AN.

uln2003an ic

uln2003an datasheet

Click here to access the ULN2003AN IC Datasheet

As I flipped the board to desolder the IC for replacement I noticed the solder bridge between the two wires which confirm the damage seen on that IC. Right away, I fixed that solder bridge and continued with the installment of the IC.

damaged ic

The damage was extended to the bottom of the IC as well. I have plenty of the  same exact part in the shop for this IC is used a lot in treadmills.

how to repair a massage chair with no power

Once the IC was replaced and everything was put together thanks to my helper, I powered up the machine and as seen in the photo, the machine was up and running.

how to fix and repair a broken massage chair

My helper is trying out the massager and seems like he was ok with it because he wanted to sit on that chair for a long time.

Mission Accomplished.

This article was prepared for you by Waleed Rishmawi, one of our ‘Master Authors’ and currently working in the Bethlehem area of Palestine repairing electrical and electronic equipment.

P.S- Do you know of any your friends who would benefit from this content that you are reading now? If so, forward this website to your friends or you can invite your friends to subscribe to my newsletter for free in this Link.

Note: You can check his previous article on How To Repair A Remote Control Car

Likes(61)Dislikes(0)

9 Comments

  1. Parasuraman S

    July 30, 2021 at 12:20 pm

    Congratulations on your developing an assistant! How I wish I had a son who would take interest in servicing and lend me a hand! Both of my sons, who are employed, do not have any interest or convenience to do so! My elder son is a qualified electronic engineer but does not have time or interest to do any type of service job! Second son is staying in Bangalore (a 500Km away city)!

    A good troubleshooting and solution! Many thanks for the tips and data shared!

    Likes(6)Dislikes(0)
    • Waleed Rishmawi

      July 30, 2021 at 3:04 pm

      Parasuraman: you are most welcome. my son is still not fully interested in my kind work. He is there because there is not school and he is just spending time but once in a while I interest him in using a screwdriver to take apart something, testing a playstation after it was serviced. He likes the fact that he gets paid for doing such work and he is saving money for school. so in a way, I love having him in the shop, helping me in any way he can and at the same time creating self dependency and responsibilities he can uses in his future. have a blessed day

      Likes(3)Dislikes(0)
      • Parasuraman S

        July 31, 2021 at 8:40 am

        Good and responsible upbringing! Your son is really lucky to have a father like you!

        Likes(0)Dislikes(0)
  2. Albert van Bemmelen

    July 30, 2021 at 1:20 pm

    Good repair after a strange solder bridging short circuit killed the ULN chip. The question remains how the solderbridge did get there?

    Likes(2)Dislikes(0)
    • Waleed Rishmawi

      July 30, 2021 at 3:07 pm

      Albert: thanks man. I asked the customer about that and he said that he is an electrician and he wanted to solder the cold joints thinking that it would solve the problem but in fact, he killed the device instead. have a blessed day

      Likes(2)Dislikes(0)
  3. Yogesh Panchal

    July 30, 2021 at 1:47 pm

    well done! Waleed

    Likes(0)Dislikes(0)
    • Waleed Rishmawi

      July 30, 2021 at 3:07 pm

      Yogesh: thanks man. have a blessed day

      Likes(0)Dislikes(0)
  4. Babu M S

    July 30, 2021 at 10:00 pm

    Good job . One more new thing learned from this article.You please convey my best wishes to your son.

    Likes(1)Dislikes(0)
    • Waleed Rishmawi

      July 31, 2021 at 3:46 pm

      Babu: thanks man. I am glad you liked it. my son thank you as well. have a blessed day

      Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Open

Close