Don't Miss


About The Blue ESR Meter Chart

By on September 12, 2008

esr chart

I have some Blue ESR Meter buyers found it difficult to understand the chart readout printed in front of the Blue ESR Meter. Infact here is a link where you can use it for easy reference. Please Click HERE to visit the chart.

Likes(7)Dislikes(1)

8 Comments

  1. Rizwan

    July 31, 2010 at 8:11 pm

    Hi i am still having problems understanding the chart i recived my blue esr meter today. but i am crap at understanding numbers. i tried out a 100v 1000uf cap i got .03 on my meter (meter has two decimal points e.g .0.0). is the cap bad or good. i am embarrassingly crap at reading and understanding numbers.

    Likes(0)Dislikes(0)
  2. admin

    August 1, 2010 at 2:57 am

    HI RIZWAN,

    It is a good cap if according to the chart and not the chart on the meter. It is easier to read from the above chart then the chart provided on the meter. If you refer to the chart you will not see the esr ohm value for 100v but you can roughly take the inbetween 63v and 160v esr value. Any value that is under the chart value is good.

    Jestine

    Likes(0)Dislikes(0)
  3. hasan

    February 1, 2011 at 3:40 pm

    hi sir jestine yes i 20!! My best wishes to yu and your family thanks for your news latter. I have sony vedeo projector 3lcd model no.vpl-es4 the bullb blew. The original bulb is 240 us dollar is there any modification with any cheeper bulb with 2000 lumens am willing to try .the last thing ive repaired many tv with dry joint at vertical section some at the crt board and many e caps at secondary out put all thanks to you and your team happy 2011

    Likes(1)Dislikes(0)
  4. admin

    February 2, 2011 at 9:12 am

    HI Hasan,

    Thanks but sorry i have no info on this.

    Jestine

    Likes(0)Dislikes(0)
  5. Daniel Johnson

    July 31, 2016 at 11:32 am

    Do you have a table with ESR values for higher voltage capacitors, specifically, 400V 100uF?

    Likes(0)Dislikes(0)
    • Jestine Yong

      August 1, 2016 at 10:54 am

      Hi Daniel,
      Sorry i do not have but you can use the chart in the link below to roughly guess the value:

      https://jestineyong.com/esr-meter-table/

      A good 100uf 400volt should be less than 0.2 Ohm. Or the best compare with the a good one and jot down the value for future reference.

      Jestine

      Likes(0)Dislikes(0)
  6. John Peplau

    October 30, 2016 at 2:53 pm

    Could I copy the chart on the meter, then take a small ruler to extend the lines further out of the graph on either sides and then draw vertical lines to create a larger chart for measuring capacitors out of range of the original graph to interpellate what the approximate value should be or just make a list of new capacitors against the ones in or out of circuit to decide what is bad ?

    Likes(1)Dislikes(0)
    • Jestine Yong

      October 30, 2016 at 10:39 pm

      Hi John,

      Yes you can do that.

      Jestine

      Likes(0)Dislikes(0)

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Free Report